PA5005.332NLT Pulse

I A T F SMT Power Inductors High Current Composite Inductor - PA5005.XXXNLT and PM2205.XXXNLT POWER PRODUCTS Height: 5.0mm Max Footprint: 6.8mm x 6.6mm Max Current Rating: up to 24Apk Inductance Range: 0.82uH to 8.2uH High current, low DCR, and high efficiency High reliability Minimized acoustic noise and minimized leakage flux noise Available in Commercial (PA5005) and Automotive (PM2205) grades Electrical Specifications 25C, Operating Temperature Range - 55C to +155C 2 Part Number DC Resistance Saturation 3 Rated Inductance Mechanical K Factor Current 100KHz, 0.1V Current D for TYP. MAX. (25C) 6 Commerical Automotive Core Loss uH20% A m m A 0.3 PA5005.821NLT PM2205.821NLT 0.82 21 3.8 4.18 20 132.2 5.3 PA5005.102NLT PM2205.102NLT 1.0 20 4.1 4.52 18 132.2 5.3 PA5005.122NLT PM2205.122NLT 1.2 18 5.3 5.83 16 109.2 5.3 PA5005.152NLT PM2205.152NLT 1.5 17 5.7 6.3 14.5 93 5.3 PA5005.182NLT PM2205.182NLT 1.8 16 6.4 7.1 13.5 93 5.3 PA5005.222NLT PM2205.222NLT 2.2 13 7.7 8.5 12 81 5.2 PA5005.332NLT PM2205.332NLT 3.3 11 11.2 12.5 10 64.4 5.2 PA5005.432NLT PM2205.432NLT 4.3 9 15.1 16.2 8.5 53.4 5.2 PA5005.472NLT PM2205.472NLT 4.7 8.5 16.7 18.4 8 49.2 5.2 PA5005.562NLT PM2205.562NLT 5.6 7.0 20.0 22.0 8.3 5.2 PA5005.682NLT PM2205.682NLT 6.8 6.6 23.1 25.4 7 5.2 PA5005.822NLT PM2205.822NLT 8.2 6.2 28.6 31.5 6.8 5.2 Notes: 1. Actual temperature of the component during system operation (ambient plus other cooling provisions all affect the part temperature. Part temperature should be temperature rise) must be within the standard operating range. verified in the end application. 2. The saturation current is the current at which the initial inductance is guaranteed to 5. The PM2205.XXXNLT part numbers are AEC-Q200 and IATF16949 certified. The drop by no more than 40%. The typical inductance at a specified current can be found mechanical dimensions are 100% tested in production but do not necessarily meet a on the typical performance curves. product capability index (Cpk) >1.33 and therefore may not strictly conform to PPAP. 3. The rated current is the DC current required to raise the component temperature by 6. Parts shown in bold are standard catalog parts and are available through sample approximately 40C. Take note that the components performanc varies depending stock and distribution. Parts in lighter font are available but are not necessarily held on the system condition. It is suggested that the component be tested at the system in sample stock or distribution and lead times may be longer. Please contact Pulse level, to verify the temperature rise of the component during system operation. for availability. 4. The part temperature (ambient+temp rise) should not exceed 155C under worst 7. Special Characteristics case operating conditions. Circuit design, PCB trace size and thickness, airflow and Power.PulseElectronics.com P809. D (07/20) 1 1 6 9 4 90 SMT Power Inductors High Current Composite Inductor - PA5005.XXXNLT and PM2205.XXXNLT POWER PRODUCTS Mechanical PA5005.XXXNLT and PM2205.XXXNLT D A C H E XXX 1R2 B F 16D/C02 FINAL LAYOUT SUGGESTED PAD LAYOUT Series A B C D E F L G H PA5005/PM2205 SEE SPEC TABLE 2.60.25 5.6 (REF) 2.5 (REF) 5.6 (REF) 6.60.2 6.40.2 4.80.2 1.40.2 All Dimensions in mm. TAPE & REEL INFO Blank portions Chip cavity Blank portions K P1 200mm or more 400mm or more G Direction of tape SURFACE MOUNTING TYPE, REEL/TAPE LIST REEL SIZE (mm) TAPE SIZE (mm) QTY A G P W K PCS/REEL 1 0 PA5005/PM2205 330 16.4 12 16 5.3 800 Power.PulseElectronics.com P809. D (07/20) 2 W L A G