QPB9015 xPON Video Receiver with integrated VCA xPON Video Receiver Product Description The QPB9015 is a video receiver integrated circuit (IC) which provides a low noise analog interface to optical access triplexer modules used in single family ONTs in fiber to the premise (FTTP) applications. The QPB9015 28 pin, 11.0 mm x 11.0 mm x 1.375 mm package exhibits low input noise and distortion to meet critical FTTP link requirements. QPB9015 employs an integrated voltage controlled attenuator that provides, with external control circuitry, automatic gain control to Product Features maintain a constant +19 to +23 dBmV / channel output to insure consistent video quality. 45 1218 MHz Operational Bandwidth Efficient Power Consumption: 1.5 W Low Noise: 3.5 pA / Hz Equivalent Input Noise Functional Block Diagram Current (EINC) Linearity: -65 dBc CSO and -66 dBc CTB at +22 Vdd1,Vdd2 dBmV RF Output per Channel (79-NTSC Equivalent Channels) QPB9015 Vcc Integrated VCA, 25 dB Attenuation Range Temperature Sensing Feature OUTPUT Photo Diode Driver TIA Temperature Att. adjust Sensing Applications xPON RF Overlay Video Receiver for FTTX Triplexer- Equipped Optical Network Termination (ONT) and RFoG Network Interface Unit (NIU) Ordering Information Part No. Description QPB9015SB Sample bag 5 pcs QPB9015SR 7 Reel with 100 pcs QPB9015TR7 7 Reel with 250 pcs QPB9015PCBA-410 Fully assembled Evaluation Board Data Sheet Rev E, Feb 19, 2021 Subject to change without notice 1 of 15 www.qorvo.com QPB9015 Absolute Maximum Ratings Recommended Operating Conditions Parameter Min Typ Max Units Parameter Value/R ang e Detector Bias over-voltage (Vcc) +15 V Detector Bias Voltage (Vcc) +11.4 +12 +12.6 V DC Supply over-voltage (Vdd1,Vdd2, Vc, +6V MODE) DC Supply Voltage (Vdd1,Vdd2) +4.5 +5 +5.5 V Storage Temperature 40 to 100C Operating Mounting Base Operating Mounting Base Temperature Temperature -40 +85 C 40 to 85C Exceeding any one or a combination of the Absolute Maximum Rating Electrical specifications are measured at specified test conditions in conditions may cause permanent damage to the device. Extended application circuit. Specifications are not guaranteed over all application of Absolute Maximum Rating conditions to the device may recommended operating conditions. reduce device reliability. Electrical Specifications tested in evaluation circuit Conditions (Vcc=12V, Vdd1=Vdd2=5V, Parameter Min Typ Max Units TMB=30C, ZL=75 ATT=020dB) Steady state operation, current draw during attenuation Supply Current (I ) 300 mA DD state transitions is higher. Frequency Range 45 1218 MHz 1 Spectral sensitivity 0dBm optical input, 1310nm 900 V/W Gain (O/E) 1218MHz, ATT=0dB 37 dBA/W 2 Gain Slope 45MHz to 1218MHz 1 dB 3 Gain Flatness 45MHz to 1218MHz 2 dB Output Return Loss (S22) 45MHz to 1218MHz -15 dB Equivalent Input Noise (EINC) 45MHz to 1218MHz, ATT=0dB 3.5 pA/ Hz Optical Input Power +2 dBm Source: 79 NTSC analog channels (55.25 to 547.25MHz), flat, CSO -65 dBc OMI = 2.82%/ch DUT: +2 dBm optical input power, attenuator set to CTB -66 dBc RFOUT = +22 dBmV per channel Voltage Control Range, Positive MODE Pin Logic High: Control voltage Vc=5V is lowest insertion loss 0 03 5 V Attenuation Slope Voltage Control Range, Negative MODE Pin Logic Low: Control voltage Vc=0V is lowest insertion loss 0 03 5 V Attenuation Slope MODE Pin Logic Low 0.4 V MODE Pin Logic High 1 V Attenuator Range 025 dB Thermal Resistance T taken at +85 C from backside of PCB under the QPB9015 26.5 K/W REF 1. Measured between OPS pin and GND on evaluation board. 2. The slope is defined as the difference between the gain at start frequency and the gain at stop frequency. 3. Measured as sum of positive and negative deviation from a straight line between gain at start frequency and gain at stop frequency. Composite Second Order (CSO) - The CSO parameter (both sum and difference products) is defined by ANSI/SCTE 6. Composite Triple Beat (CTB) The CTB parameter is defined by ANSI/SCTE 6. Data Sheet Rev E, Feb 19, 2021 Subject to change without notice 2 of 15 www.qorvo.com