QPQ1286 TDD B40 BAW Band Pass Filter (50MHz) General Description The QPQ1286 is a high-performance Bulk Acoustic Wave (BAW) filter designed to meet the strict LTE rejection requirements for use in B40, Sub-Band 2320-2370 MHz QPQ1286 is specifically designed to meet the high- performance expectations of insertion loss and rejection for LTE TDD systems under all operating conditions. 3 Pin 2 x 1.6 mm leadless SMT Package The QPQ1286 uses common module packaging Product Features techniques to achieve the industry standard 2.0 x 1.6 x 0.73 mm footprint. Highly selective BAW filter achieving low insertion loss over full bandwidth and operating conditions Performance -40 C to +90 C A Excellent Wi-Fi rejection Single-ended operation S No Matching required for operation at 50 High Power Handling Compatible for Small Cells Small Size Functional Block Diagram RoHS compliant (2011/65/EU), Pb-free P b PIN 1 Location Applications RF In A 1 For Band 40 TD-LTE applications 2320 2370 MHz Sub-Band S For Small Cells Base Stations RF Out A 2 3 Top View TOPxRAY TOPxRAY PINS VIEW VIEW Pin Configuration Ordering Information Pin No. Label Part No. Description TQQ6421 01 UNIT, 01.60mm X 02.00mm, 7 LAYER, 0.40mm MOLD CAP, 1 RF in QPQ1286TR7 2,500 pieces on a 7 reel (standard) 2 RF out QPQ1286EVB Evaluation Board TOPxRAY 1:1 A3H TOPxRAY PINS 3 Ground Datasheet, November 5, 2018 Subject to change without notice - 1 of 8 - www.qorvo.com QPQ1286 TDD B40 BAW Band Pass Filter (50MHz) Absolute Maximum Ratings Life Test Parameter Rating Conditions Rating (1) +29 dBm, LTE SIGNAL Storage Temperature 40C to +125C PAR = 8dB, 5MHz, 16 QAM >175,300 hrs. (2) Operating Temperature 40C to +105 C + 90 C (1) Operation of this device outside the parameter ranges given Power rating is valid when Power is injected into Pin 1 may cause permanent damage. (2) Device will function but it is not guaranteed to meet electrical specifications. (1) Electrical Specifications Test conditions unless otherwise specified. Temperature Range: -40C to +90C Parameter Conditions Min Typ Max Units Maximum Insertion Loss 2320 2370 MHz - 1.9 2.8 dB Input / Output VSWR 2320 2370 MHz - 1.6:1 2.1:1 - Input / Output Return Loss 2320 2370 MHz 9.0 14 - dB (2) Amplitude Variation 2320 2370 MHz - 0.9 1.6 dB (3) Group Delay Ripple 2320 2370 MHz - 7 25 ns p-p (4) Phase Ripple 2320 2370 MHz - 11 35 p-p 2405 2440 MHz (Channel 1 - 7) 42 47 - (5) Attenuation in WIFI Band dB 2440 2480 MHz (Channel 8 - 14) 38 40 - 10960 MHz 41 45 - 9611709 MHz 31 33 - 17101880 MHz 30 32 - 19202170 MHz 30 32 - 21712295 MHz 10 23 - 23952405 MHz 10 17 - (6) Attenuation dB 24802500 MHz 36 38 - 25003660 MHz 32 34 - 37504600 MHz 34 37 - 46004800 MHz 43 49 - 49016000 MHz 25 29 - 60018000 MHz 30 34 - nd 2 Harmonic Pin = +29 dBm (2320 - 2370 MHz) - - 86 - 65 dBc (7) Source/Load Impedance Single-ended - 50 - Notes: 1. All specifications are based on the QORVO schematic for the main reference design shown on page 4 2. Amplitude Variation is defined as the difference between the lowest loss and the highest loss within defined frequency points 3. This is defined as the worst difference between a peak and adjacent valley within defined frequency points 4. Typical values are and average of 20 pieces measured at a temperature of +25 C 5. Attenuation is referenced to ZERO dB 6. Attenuation is referenced to ZERO dB 7. This is the optimum impedance in order to achieve the performance shown Datasheet, November 5, 2018 Subject to change without notice - 2 of 8 - www.qorvo.com