857193 RFMD + TriQuint = Qorvo 725.5 MHz SAW Filter Applications General purpose wireless Wireless infrastructure Base Station Applications SMP 12, 3.00 X 3.00 X 1.22 mm Product Features Functional Block Diagram Usable bandwidth of 45 MHz For wideband applications 6 1 Low Loss Gnd Gnd Single-ended operation Matching required for operation at 50 Input Output 2 5 Small Size: 3.00 x 3.00 x 1.22 mm Ceramic Surface Mount Package (SMP) 3 4 Gnd Gnd Hermetically sealed Pb RoHS compliant (2002/95/EC), Pb-free Pin Configuration Single Ended General Description EEEnded./Bal-B 857193 is a general purpose Uplink filter for Band 28. Pin No. Label This filter was specifically designed in a 3x3mm 2 Input hermetic package for base station applications and is 5 Output part of our wide portfolio of RF filters in the same 1.3,4,6 Ground package. Low insertion loss, coupled with high attenuation and excellent power handling, makes this filter a natural choice for our customers Uplink RF filtering needs. Ordering Information Part No. Description 857193 Product description 857193-EVB Evaluation board description Standard T/R size = 5000 units/reel Data Sheet: Rev C 08-24-15 Disclaimer: Subject to change without notice - 1 of 6 - www.triquint.com /w w w .qo rv o .co m 2015 TriQuint 857193 RFMD + TriQuint = Qorvo 725.5 MHz SAW Filter (1) Absolute Maximum Ratings Parameter Rating Notes 1. Operation of this device outside the parameter Storage Temperature -40 to +85C ranges given may cause permanent damage. Operable Temperature -30 to +105C 2. Input power with applied CW signal at =105 C in (2) RF Input Power +22 dBm the 703 748MHz frequency band for 24 hrs. 3. Input Power with applied CW signal at +105C for 24 hours. (1) Electrical Specifications (2) Specified Temperature Range: -30C to +105C (3) (4) Parameter Conditions Min Typ Max Units Center Frequency - 725.5 - MHz Maximum Insertion Loss 703 748 MHz - 2.3 4.0 dB - 0.8 1.0 dB p-p (5) 703 748 MHz Amplitude Variation Any 5 MHz span within 703 -748 MHz 0.4 0.6 dB p-p (6) Temperature Drift 703 748 MHz - 0.25 0.3 dB Phase Ripple 703 748 MHz - 21 35 deg. p-p (7) 703 748 MHz EVM - 1.6 2.0 % Any 3.84 MHz span within 703 748 MHz (8) Tones 5 MHz separated, power >5 dBm per tone IIP3 44 50 - dBm Absolute Delay 703 748 MHz - 17 30 ns Group Delay Variation 703 748 MHz - 20 30 ns p-p 10 100 MHz 30 60 - dB 430 480 MHz 30 36 - dB 480 648 MHz 20 25 - dB (9) 773 830 MHz 20 28 - dB Relative Attenuation 936 971 MHz 20 30 - dB 1615 1660 MHz 45 60 - dB 1660 2690 MHz 20 55 - dB 3510 3800 MHz 20 50 - dB (10) Input/Output VSWR 703 748 MHz - 1.7 2.0:1 - (11) Load/Source Impedance single-ended - 50 - Ohms Notes: 1. All specifications are based on the TriQuint schematic shown on page 3 2. In production, devices will be tested at room temperature to a guardbanded specification to ensure electrical compliance over temperature 3. Electrical margin has been built into the design to account for the variations due to temperature drift and manufacturing tolerances 4. Typical values are based on average measurements at room temperature 5. Amplitude Variation is defined as the difference between the lowest loss and the highest loss within defined frequency points 6. Temperature Drift specification is defined on Page 3 and is guaranteed by design and will not be measured in production. 7. Measured with a RRC filtered QPSK modulated signal 8. To be measured only during engineering development 9. Relative to the maximum insertion loss 10. 2% tolerance on the matching component values would be needed to achieve this specification 11. This is the optimum impedance in order to achieve the performance shown Data Sheet: Rev C 08-24-15 Disclaimer: Subject to change without notice - 2 of 6 - www.triquint.com /w w w .qo rv o .co m 2015 TriQuint