856977 Qorvo

856977 787.5 MHz SAW Filter Applications General purpose wireless Wireless infrastructure 3G, 4G, Multistandard Repeaters Product Features Functional Block Diagram Top view Usable bandwidth 21 MHz High attenuation 6 1 Gnd Gnd Low Loss Single-ended operation Matching required for operation at 50 Input Output 2 5 Small Size: 3.00 x 3.00 x 1.22 mm Ceramic Surface Mount Package (SMP) Hermetically sealed 3 4 Gnd Gnd RoHS compliant, Pb-free General Description Pin Configuration Pin SE Description Uplink filter combining bands 13 and 14 for general 2 Input purpose wireless applications. This filter was specifically 5 Output designed in a 3x3mm hermetic package for base station 1,3,4,6 Case Ground applications and is part of our wide portfolio of RF filters in the same package. Low insertion loss, coupled with high attenuation and good power handling, makes this filter a natural choice for our customers uplink RF filtering needs. Ordering Information Part No. Description 856977 packaged part 856977-EVB evaluation board Standard T/R size = 5000 units/reel. Data Sheet: Rev A 5/18/11 - 1 of 6 - Disclaimer: Subject to change without notice e 2011 TriQuint Semiconductor, Inc. Connecting the Digital World to the Global Network 856977 787.5 MHz SAW Filter Specifications (1) Electrical Specifications (2) Specified Temperature Range: -30 to +85 C (3) (4) Parameter Conditions Min Typical Max Units Center Frequency - 787.5 - MHz Maximum Insertion Loss 777 798 MHz - 2.05 2.75 dB (5) Amplitude Variation 777 798 MHz - 0.5 1.4 dB Amplitude Ripple (any 5 MHz in 777 798 MHz - 0.5 1.0 dB p-p (6) passband) (6) Amplitude Ripple 777 798 MHz - 0.5 1.2 dB p-p Phase Ripple 777 798 MHz - 42 55 deg p-p Group Delay Ripple 777 798 MHz - 39 60 ns p-p Absolute Group Delay 777 798 MHz - 48 55 ns (7) Attenuation 70 120 MHz 50 74 - dB 430 470 MHz 40 66 - dB 591 614 MHz 30 60 - dB 746 765 MHz 15 23 - dB 765 768 MHz 5 23 - dB 818 824 MHz 10 21 - dB 843 857 MHz 40 53 - dB 1005 1026 MHz 30 55 - dB 1688 1711 MHz 42 52 - dB 2010 2052 MHz 30 58 - dB 2922 2964 MHz 20 42 - dB Input/Output VSWR 777 798 MHz - 1.4 2.0 - (8) Source/Load Impedance Single-ended - 50 - Notes: 1. All specifications are based on the TriQuint schematic for the main reference design shown on page 3 2. In production, devices will be tested at room temperature to a guardbanded specification to ensure electrical compliance over temperature 3. Electrical margin has been built into the design to account for the variations due to temperature drift and manufacturing tolerances 4. Typical values are based on average measurements at room temperature 5. Describes the total variation over the defined frequency range 6. This is defined as the worst difference between a peak and adjacent valley within defined frequency points 7. Relative to passband loss at center frequency 8. This is the optimum impedance in order to achieve the performance shown Absolute Maximum Ratings Parameter Rating (9) o Operating Temperature -40 to +85 C o Storage Temperature -40 to +85 C o (10) Input Power (10Khrs 55 C under CW signal) +20 dBm 9. Device may operate over this range with degraded Electrical Specifications 10. Device can also meet +22dBm power for an applied CW modulated CW signal at 55 deg C for a minimum of 125 hours in the 777.0- 798.0 MHz frequency band Operation of this device outside the parameter ranges given above may cause permanent damage. Data Sheet: Rev A 5/18/11 - 2 of 6 - Disclaimer: Subject to change without notice e 2011 TriQuint Semiconductor, Inc. Connecting the Digital World to the Global Network