RFMD + TriQuint = Qorvo RFFM4555 RFFM4555 Wi-Fi Integrated Front End Module 4.9GHz to 5.925GHz Package: DFN, 8-pin, 1.5mm x 1.5mm x 0.455mm The RFFM4555 is a front end module (FEM) designed for 802.11a/n/ac Features applications. The integrated single-pole double throw switch and low 13dB LNA Gain noise amplifier with bypass greatly reduces the layout area, bill of materials and manufacturability cost in the customer application. The 6dB Bypass Loss RFFM4555 is optimized to pair with Wi-Fi power amplifiers such as the 2.6dB Noise Figure RFPA5512/RFPA5522/RFPA5542 to create a complete Tx and Rx TX to ANT path loss of 0.6dB solution. The device is provided in a 1.5mm x 1.5mm x 0.455mm DFN Max Power at TX Input of 33dBm package that meets or exceeds the power requirements of 2.4GHz Rejection IEEE802.11a/n/ac Wi-Fi RF systems. Input and Output Matched to 50 Optimized to pair with the RFPA55X2 Family Power Amplifiers ANT TX 1 8 Applications Customer Premise Equipment VRX GND 2 7 (CPE) Wireless Access Points, Gateways RX VTX 3 6 Routers Set-Top Box Applications LNAEN VDD 4 5 Picocell/Femtocell Functional Block Diagram Ordering Information RFFM4555SB Standard 5-piece Sample Bag RFFM4555SQ Standard 25-piece Sample Bag RFFM4555SR Standard 100-piece Reel RFFM4555TR7 Standard 2500-piece Reel RFFM4555PCK-410 Fully Assembled Evaluation Board + 5 pieces RFPA5512PCK-411 Integrated RFPA5512+RFFM4555 EVB + 5 pieces RFPA5522PCK-411 Integrated RFPA5522+RFFM4555 EVB + 5 pieces Revision DS20150626 Disclaimer: Subject to change without notice 1 of 6 2015 RF Micro Devices, Inc. www.rfmd.com / www.qorvo.com RFMD + TriQuint = Qorvo Absolute Maximum Ratings Caution ESD sensitive device. Parameter Rating Unit DC Supply Voltage (No RF applied) -0.5 to +6 V DC DC Supply Current 100 mA RFMD Green: RoHS status based on EU Operating Case Temperature -40 to +85 C Directive 2011/65/EU (at time of this Storage Temperature -40 to +150 C document revision), halogen free per IEC 61249-2-21, < 1000ppm each of Maximum TX Input Power into 50 Load for 11a/n/ac (No Damage) +33 dBm antimony trioxide in polymeric materials and red phosphorus as a flame retardant, Maximum RX Input Power (No Damage) +12 dBm and <2% antimony in solder. Bypass Mode Maximum RX Input Power (No Damage) +25 dBm Exceeding any one or a combination of the Absolute Moisture Sensitivity Level (260C JEDEC J-STD-020) MSL2 Maximum Rating conditions may cause permanent damage to the device. Extended application of Absolute Maximum Rating conditions to the device may reduce device reliability. Specified typical performance or functional operation of the device under Absolute Maximum Rating conditions is not implied. Nominal Operating Parameters Specification Parameter Unit Condition Min Typ Max Compliance IEEEE802.11a/n/ac Operating Frequency 5.180 5.925 GHz Extended Operating Frequency 4.900 5.925 GHz Functional with reduced performance Operating Temperature -40 +25 +85 C Power Supply V 3.3 5.0 V LNA supply voltage only DD Control Voltage - High 2.8 3.1 V V VTX, VRX and LNAEN should not exceed V DD DD Control Voltage Low 0 0.2 V VTX, VRX and LNAEN Transmit Performance T=+25C, V =3.3-5V, VTX=High, LNAEN & VRX=Low, DD (TX-ANT) CW Signal Unless otherwise noted Insertion Loss 0.6 1.2 dB Linear output Power 23 dBm 11ac 80MHz Dynamic EVM -45 -40 dB 0.6 1 % TX Port Return Loss 20 35 dB ANT Port Return Loss 20 35 dB nd 2 Harmonics -50 -45 dBm/MHz P = 28dBm 802.11a 6MBps OUT rd 3 Harmonics -50 -40 dBm/MHz P = 28dBm 802.11a 6MBps OUT Input P 30 33 dBm 0.1dB ANT-RX Isolation 25 35 TX Mode: TX enabled and maximum power Receive Performance T=+25C, V =3.3-5V, VTX=Low, LNAEN & VRX=High, DD (ANT-RX) LNA On CW Signal Unless otherwise noted Gain 10.5 13 dB Small Signal Gain 2400-2500MHz -15 -12 dB Noise Figure 2.6 3 dB RX Port Return Loss 5 10 dB ANT Port Return Loss 3 7 dB Input P1dB -10 -5 dBm Current Consumption 8 13 20 mA Revision DS20150626 Disclaimer: Subject to change without notice 2 of 6 2015 RF Micro Devices, Inc. www.rfmd.com / www.qorvo.com