RFFM6205 RFFM6205 2.0V to 4.0V, 2.4GHz Front End Module The RFFM6205 is a complete integrated solution in a single Front End Module (FEM) for Zigbee applications in the 2.4GHz to 2.5GHz band Package: QFN, 16-pin, and Bluetooth transmitter applications. The ultra-small factor and 2.5mm x 2.5mm x 0.5mm integrated matching minimizes layout area in the customer s application and greatly reduces the number of external components. This simplifies Features the total front end solution by reducing the bill of materials, system Tx Output Power = 14dBm footprint, and manufacturing cost. Integrated RF Front End The FEM integrates a power amplifier (PA) plus harmonic filter in the Module with Rx/Tx switch, PA, transmit (TX) path, a low noise amplifier (LNA) in the receive (RX) path, Filter, LNA, Bidirectional Thru path and a low loss bidirectional through mode path. The RFFM6205 and 2-SP3T Switch incorporates two single-pole triple-throw (SP3T) switches to provide a 50 single-ended Bidirectional single port for TDD access and a single antenna port for TX, RX, and Transceiver Interface. through mode paths. The device is provided in a 2.5mm x 2.5mm x Voltage Range = 2.0V to 4.0V 0.5mm, 16-pin QFN package. Rx Noise Figure = 2.5dB Applications ZigBee 802.15.4 Based Systems for Remote Monitoring and Control AA Battery Operation 2.4GHz ISM Band Applications Smart Meters for Energy Management Bluetooth Transmitter systems Functional Block Diagram Ordering Information RFFM6205SB Standard 5 piece bag RFFM6205SQ Standard 25 piece bag RFFM6205SR Standard 100 piece reel RFFM6205TR7 Standard 2500 piece reel RFFM6205PCK-410 Fully assembled evaluation board w/5 pc bag 1 of 8 RFFM6205 Data Sheet Revision DS20190924 Disclaimer: Subject to change without notice www.qorvo.com RFFM6205 Absolute Maximum Ratings Caution ESD sensitive device. Parameter Rating Unit Voltage 4.5 V Operating Temperature -40 to +125 C RFMD Green: RoHS status based on EU Storage Temperature -40 to +150 C Directive 2011/65/EU (at time of this document revision), halogen free per IEC Maximum Input Power to PA +20 dBm 61249-2-21, < 1000ppm each of antimony Maximum Input Power to LNA +5 dBm trioxide in polymeric materials and red phosphorus as a flame retardant, and ESD, HBM (Pin-to-GND) 500 V <2% antimony in solder. ESD, CDM (Pin-to-GND) 500 V Exceeding any one or a combination of the Absolute Maximum Rating conditions may cause permanent Moisture Sensitivity MSL 2 damage to the device. Extended application of Absolute Maximum Rating conditions to the device may reduce device reliability. Specified typical performance or functional operation of the device under Absolute Maximum Rating conditions is not implied. Nominal Operating Parameters Specification Parameter Unit Condition Min Typ Max Specifications must be met across supply voltage, control voltage, and temperature ranges unless otherwise specified TX Frequency 2405 2485 MHz RX Frequency 2405 2485 MHz Bypass Frequency 2405 2485 MHz ANT RF Port Impedance 50 RFIO Port Impedance 50 V 2.0 3.0 4.0 V BAT Off Mode Current - Leakage V TX = 3.0V, C EN = Low, V RX = 3.0V, DD DD C TX = Low, C RX = Low, C BYP = Low, Temp =25C Supply Current - IDDTX 50 200 nA Supply Current - IDDRX 50 200 nA C RX Current 1.0 nA C TX Current 1.0 nA C BYP Current 1.0 nA Transmit Mode - Power VDD TX = 3.0V, C EN = High, VDD RX = 3.0V, Amplifier C TX =High, C RX =Low, C BYP =Low, Temp =25C unless otherwise specified Input Return Loss 10.0 dB Output Return Loss 8.0 dB Small Signal Gain 11.0 14.0 dB Gain Flatness -0.3 0.3 dB Rated Output Power 15.0 dBm VDD TX = 4.0V 13.0 14.0 dBm VDD TX = 3.3V 12.5 13.5 dBm VDD TX = 3.0V 10.0 11.0 dBm VDD TX = 2.0V 2 of 8 RFFM6205 Data Sheet Revision DS20190924 Disclaimer: Subject to change without notice www.qorvo.com