RFFM5765Q RFFM5765Q Tested in Accordance with AEC-Q100 802.11b/g/n WiFi Front End Module Package: QFN, 16-pin, 3.0mm x 3.0mm x 0.5mm The RFFM5765Q provides a complete integrated solution in a single Features front end module (FEM) for automotive WiFi applications, 802.11b/g/n, Single Supply Voltage 3.0V to 4.8V and Bluetooth systems. The ultra-small form factor and integrated matching greatly reduces the number of external components and Input and Output Matched to 50 layout area in the customer application. This simplifies the total front end Gain = 30dB solution by reducing the bill of materials, system footprint, and POUT = 19dBm, 11g, 64QAM at manufacturing cost. The RFFM5765Q integrates a 2.4GHz power <4% Dynamic EVM amplifier (PA), low noise amplifier (LNA), power detector coupler for POUT = 22dBm, 11b, CCK 11Mbps, improved accuracy, and some filtering for harmonic rejection. The Spectral Mask and ACPR compliant RFFM5765Q is capable of receiving WiFi and Bluetooth simultaneously and is tested in accordance with AEC-Q100 standard. The device is provided in a 3.0mm x 3.0mm x 0.5mm, 16-pin package. This module Applications meets or exceeds the RF front end needs of IEEE 802.11b/g/n WiFi RF Automotive WiFi systems. WiFi Direct Automotive Diagnostics WiFi Infotainment 2.5GHz ISM Band Solutions Portable Battery-Powered Equipment Functional Block Diagram Ordering Information RFFM5765QSQ Standard 25-piece bag RFFM5765QSR Standard 100-piece bag RFFM5765QTR7 Standard 2500-piece reel RFFM5765QPCK-410 Fully assembled evaluation board DS R ev O Subject to change without notice 1 of 15 RFFM5765Q Absolute Maximum Ratings Caution ESD sensitive device. Parameter Rating Unit DC Supply Voltage (Continuous with No Damage) 6.0 V DC Supply Current 700 mA RFMD Green: RoHS status based on EU Case Operating Temperature -40 to +85 C Directive 2011/65/EU (at time of this document revision), halogen free per IEC Storage Temperature -40 to +150 C 61249-2-21, < 1000ppm each of Maximum Tx Input Power into 50 Load for 11b/g/n (No Damage) +5 dBm antimony trioxide in polymeric materials and red phosphorus as a flame retardant, Maximum Rx Input Power (No Damage) +5 dBm and <2% antimony in solder. Moisture Sensitivity MSL2 Exceeding any one or a combination of the Absolute Maximum Rating conditions may cause permanent damage to the device. Extended application of Absolute Maximum Rating conditions to the device may reduce device reliability. Specified typical performance or functional operation of the device under Absolute Maximum Rating conditions is not implied. Nominal Operating Parameters Specification Unit Condition Parameter Min Typ Max 2.4GHz Transmit Parameters Compliance IEEE802.11b/g/n Standards, FCC CFG 15.247, .205, .209, EN, and JDEC V = 3.0V to 4.2V V = 3.0V to 3.2V P (g/n) = 19dBm Operating Conditions CC REG OUT Frequency 2412MHz to 2484MHz Switch Control voltage: 3.0V to 3.6V 11g 54Mbps and 11n MCS7 signals Temp = -40C to +85C Unless noted otherwise. Frequency 2.4 2.5 GHz Power Amplifier Voltage Supply (V ) Voltage Supply 3.0 3.3 4.2 V CC V Voltage REG ON 3.0 3.1 3.2 V PA in ON state OFF 0.00 0.20 V PA in OFF state Output Power V > 3.0V 11g/n 17 18.5 dBm CC V > 3.3V 18 19 dBm CC 11b 19 22 dBm 11Mbps CCK signal, V > = 3.3V CC P (g/n) = Rated Output Power, 54Mbps OFDM, 50, see note 1 EVM 3.3 4 % OUT P (b) = 22dBm, 11Mbps CCK signal, V > = 3.3V, see note 4 Adjacent Channel Power OUT CC ACP1 -36 -33 dBc +/- 11MHz Offset from carrier ACP2 -56 -53 dBc +/- 22MHz Offset from carrier Gain 25.5 30 34.5 dB Gain Variation Slope At rated power and a given supply voltage Range 3.0 4.2 V V (Average) CC 0.5 dB/V V (Instantaneous) 1 dB/V CC Frequency -0.5 +0.5 dB 2.4GHz to 2.5GHz V = 3.3V, V = 3.1V, Freq = 2.45GHz Over Temperature -1.75 +1.75 dB CC REG Typical Input Power 11g/n -9 dBm 11b -5 dBm DS Rev O Subject to change without notice 2 of 15