20W Class II AC-DC LED Power Supply LIGHTLINE Features ENEC, UL, RCM and CB Certified AC/DC-Converter Active Power Factor Correction >0.95 Fused Input, Protected Output LED with 5 year Warranty 3kVAC Isolation DRIVER cUL/UL8750 Certified, CE Marked Output Connector to avoid miswiring Low Cost Long 5 Year Warranty 20 Watt PFC Description A compact 20W constant current switching power module suitable for driving high power LEDs (Vf = 3.6V). Single The output current is fixed at 350mA, 500mA, 700mA or 1050mA. Active power factor correction is standard. This series features both screw terminal and socket output connections. The socket connecter avoids the possibility of miswiring and damaging the LED load if the LEDs are preassembled into a wiring harness or lamp fitting. Output Selection Guide Part Input Voltage Input Current Nom. Output Output Max Number Range at full load Voltage Range Current (VAC) (mA) (VDC) (mA) LEDs RACD20-350 universal 260 6-56 350 15 x 1W RACD20-500 universal 260 6-40 500 11 x 2W RACD20-700 universal 260 6-29 700 8 x 2W, 8+8 x 1W RACD20-1050 universal 260 5-17 1050 6 x 3W, 5+5 x 2W Specifications (typical at 25C and after warm up time unless otherwise specified ) RoHS 2011/65/EU Input Voltage Range Standard 90-264VAC 6/6 E340696 Rated Power 20 Watts max. UL 8750 Certified Input Frequency Range 47-63 Hz cUL 8750 Certified* Power Factor Full Load, 115VAC/230VAC 0.95 ENEC 61347 Certified THD Full Load, 115VAC/230VAC 12% max. Open Circuit Voltage 350mA Version 57VDC (Zener Clamp) 500mA Version 43VDC 700mA Version 32VDC RACD20 1050mA Version 19VDC Inrush Current (<2mS) 115VAC/230VAC 10A max. Input Current 230VAC, Full Load 260mA typ. Leakage Current 115VAC/240VAC - 60/50Hz 0.5mA typ. Input Fuse Standard T1A * RACD20-700 and -1050 Output Current Accuracy (combined Tolerance, load Regulation and Line Regulation) 10% only has cUL Minimum Load Open Circuit Protected 2 LEDs Hold Up Time 18ms min. Operating Frequency 40 - 100 kHz typ. Efficiency at Full Load 83% RMS Isolation Voltage (input to output) 3kVAC / 1 minute Temperature Coefficient 0.02%/C typ. Overload Protection 120% typ. Short Circuit Protection Continuous Current Limit Output Overvoltage Protection Zener Diode Clamp Overtemperature Protection Shutdown, Automatic restart after cooling down Operating Temperature Range Ambient Temperature -20C to +50C (free air convection, according to CE/UL) Case Temperature 78.6C max. Operating Temperature Range Ambient Temperature -20C to +50C (free air convection, according to ENEC) Case Temperature 85C max. Storage Temperature Range -40C to +100C Weight 160g Packing Quantity 1pc Refer to Application Notes continued on next page www.recom-power.com REV: 0/2015 L-27RACD20 LIGHTLINE AC/DC-Converter Series (typical at 25C and after warm up time unless otherwise specified ) Specifications Humidity 95% RH max. IP Rating IP20, Indoor Use Only PCB Material Plastic Resin with Fibreglass (UL94V-0) Case Material Plastic Designed to meet Standards Electrical Lighting, EMC Emissions EN55015:2006 + A1: 2007 + A2:2009 Limits for Harmonics Emissions EN 61000-3-2:2006 EMC Compatability: Flicker and Voltage Variations EN 61000-3-3:2006 Electrical Lighting: EMC Immunity EN 61547:1995 + A1:2000 Class II Power Supply Safety complies with UL1310 FCC complies with FCC18A THD <20% Certifications LED Lighting Safety (E340696) UL8750 LED Lighting Safety (Canada) cUL8750 (RACD20-700, RACD20-1050 only) RCM (U21380) AS/NZS 61347.1:2002, IEC 61347-2-13 ENEC CE Certification, General Safety EN 61347-1: 2008 ENEC CE Certification, Safety of AC supplied Control Gear for LED Modules EN 61347-2-13: 2006 PSE J61347-1(H20), J61347-2-13(H21), J55015(H20) Design Lifetime 25C ambient >70 x 10 hours in operation Connections AC Input Screw terminal LED Output Screw Terminal LED Output 5.5mm Socket with 2mm Pin (Suitable matching plug Switchcraft S760 or similar) Note: All LED Drivers may not be used without a load. They must be switched on the primary side only. Noncompliance may damage the LED or reduce its lifetime. Characteristic Maximum Number of LED drivers per circuit breakers Condition Circuit Breaker Circuit Breaker Current Typ 10A 16A 20A 25A 115VAC, 1Ohm C 47 68 84 105 90 phase angle B 36 57 69 85 230VAC, 1Ohm 90 phase angle C 57 87 109 134 B 41 65 80 98 277VAC, 1Ohm 90 phase angle C 65 99 125 154 Package Style and Pinning + ,+ Connections CN1 Function +%+ (> 1 % L VAC in (L) *+ ( N VAC in (N) + , CN2 Function 5 : + LED+ - LED- *%+ % 5.5mm Socket* Function */ 2 Mounting screws are included Pin LED+ Shell LED- Tc=Case Temperature Measuring Point + Tolerance XX = +/-1mm XX.X = */-0.5mm The product information and specifications are subject to change without prior notice. RECOM products are not authorized for use in safety-critical applications (such as life support) without RECOMs explicit written consent. A safety-critical application is defined as an application where a failure of a RECOM product may reasonably be expected to endanger or cause loss of life, inflict bodily harm or damage property. The buyer shall indemnify and hold harmless RECOM, its affiliated companies and its representatives against any damage claims in connection with the unauthorized use of RECOM products in such safety-critical applications. L-28 REV: 0/2015 www.recom-power.com RACD20