Built-in relay to turn ON/OFF drive completely Features (zero standby current) AC/DC Converter IEC-62386 part 206 compliant Over voltage and short circuit protection DALI Selectable output for PWM / DC 0-10V / DC 1-10 Converter Screw-less connectors, easy to install RELI-DA01/R Description 1.6W The RELI-DA01/R is a DALI to analog control signal interface which is compliant DALI with the DALI IEC62386 standard. The output is selectable between 0-10V and 1-10V or PWM (1) and is compatible with all RECOM dimmable LED drivers as well as other Converter manufacturers products. The output can control several LED drivers, allowing the lighting in a whole room or office to be dimmed with just one DALI address. A built-in relay can be used to switch off the LED drivers under software control to give zero no-load consumption. The interface is universal AC powered (110VAC, 230VAC or 277VAC). Selection Guide Part Input typ. Power max. DALI Bus Dimming DALI Number Voltage Range Consumption Power Consumption Output Standard VAC W mA IEC62386 (1) PWM RELI-DA01/R 90-290 1.6 2 DC 0-10V Part-206 DC 1-10V Notes: Note1: PWM is not included in the IEC62386 standard EN61547 certified EN61347-1 certified EN61347-2-11 certified Specifications (measured ta= 25C and nominal input voltage) IEC62386-206 compliant EN55015 compliant BASIC CHARACTERISTICS Parameter Condition Min. Typ. Max. Input Voltage Range 90VAC 230VAC 290VAC Input Frequency Range 50Hz 60Hz Power Consumption 1.6W 3W Dali Bus Current Consumption 2mA Relay Switch 1 Channel 2A cont. 70A inrush REGULATIONS Parameter Value DC 0/1-10V Output Accuracy 3% max. PROTECTION Parameter Condition Value Short Circuit Protection (SCP) Dimming output continuous, current limited to 240mA Over Voltage Protection (OVP) Dali connector, Zener Diode clamp 24VDC www.recom-power.com REV.: 2/2019 L-1RELI-DA01/R AC/DC Converter Series Specifications (measured Ta= 25C and nominal input voltage) ENVIRONMENTAL Parameter Condition Value Operating Temperature Range free air convection -20C to +40C Maximum Case Temperature +46C Operating Humidity non-condensing 20% to 90% RH IP Rating IP20 MTBF MIL-HDBK-217F, G.B. 200 x 10 hours Derating Graph 100 80 60 40 20 0 -20 -10 0 10 20 30 40 50 60 Ambient Temperature C SAFETY AND CERTIFICATIONS Certificate Type (Safety) File Number Standard Lamp Controlgear - Part 1: General and safety requirements EN61347-1:2015 Lamp Controlgear - Part 2-11: Particular requirements for miscellaneous electronic IEC61347-2-11:2001, 1st Edition circuits used with luminaires EN61347-2-11:2001 Digital addressable lighting interface - Part 206: Particular requirements for control gear IEC62386-206:2009 RoHS 2+ RoHS 2011/65/EU + AM2015/863 EMC Compliance Conditions Standard / Criterion Limits and methods of measurement of radio disturbance characteristics of electri- EN55015:2013 + A1:2015 cal lighting and similar equipment Equipment for general Lighting Purpose EMC Immunity Requirements EN61547:2009 ESD Electrostatic discharge immunity test Air 2, 4, 8kV, Contact 2, 4kV IEC61000-4-2:2008, Criteria A Radiated, radio-frequency, electromagnetic field immunity test 3V/m (80-1000MHz) IEC61000-4-3:2006, Criteria A Fast Transient and Burst Immunity AC Power Port: 1.0kV IEC61000-4-4:2012, Criteria A Surge Immunity AC Power Port: L-N 0.5kV IEC61000-4-5:2005, Criteria A Immunity to conducted disturbances, induced by radio-frequency fields AC Power Port: 3V IEC61000-4-6:2008, Criteria A Power Magnetic Field Immunity 50Hz, 3A/m IEC61000-4-8:2009, Criteria A Voltage Dips and Interruptions Voltage Dips 30% IEC61000-4-11:2004, Criteria B Voltage Dips and Interruptions Voltage Interruptions >95% IEC61000-4-11:2004, Criteria B Limits of Harmonic Current Emissions EN61000-3-2:2014 Limits of Voltage Fluctuations & Flicker EN61000-3-3:2013 www.recom-power.com REV.: 2/2019 L-2 Output Power %