IDT2309 3.3V ZERO DELAY CLOCK BUFFER COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES 3.3V ZERO DELAY IDT2309 CLOCK BUFFER FEATURES: DESCRIPTION: Phase-Lock Loop Clock Distribution The IDT2309 is a high-speed phase-lock loop (PLL) clock buffer, 10MHz to 133MHz operating frequency designed to address high-speed clock distribution applications. The zero Distributes one clock input to one bank of five and one bankd delay is achieved by aligning the phase between the incoming clock and of four outputs the output clock, operable within the range of 10 to 133MHz. Separate output enable for each output bank The IDT2309 is a 16-pin version of the IDT2305. The IDT2309 accepts Output Skew < 250ps one reference input, and drives two banks of four low skew clocks. The Low jitter <200 ps cycle-to-cycle -1H version of this device operates at up to 133MHz frequency and has IDT2309-1 for Standard Drive higher drive than the -1 device. All parts have on-chip PLLs which lock IDT2309-1H for High Drive to an input clock on the REF pin. The PLL feedback is on-chip and is No external RC network required obtained from the CLKOUT pad. In the absence of an input clock, the Operates at 3.3V VDD IDT2309 enters power down, and the outputs are tri-stated. In this mode, Available in SOIC and TSSOP packages the device will draw less than 25A. The IDT2309 is characterized for both Industrial and Commercial operation. FUNCTIONAL BLOCK DIAGRAM 16 CLKOUT 2 CLKA1 PLL 1 REF 3 CLKA2 14 CLKA3 15 CLKA4 8 S2 Control 9 S1 Logic 6 CLKB1 7 CLKB2 10 CLKB3 11 CLKB4 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES AUGUST 2012 1 c 2012 Integrated Device Technology, Inc. DSC 5175/7IDT2309 3.3V ZERO DELAY CLOCK BUFFER COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES (1) PIN CONFIGURATION ABSOLUTE MAXIMUM RATINGS Symbol Rating Max. Unit VDD Supply Voltage Range 0.5 to +4.6 V REF 1 16 CLKOUT (2) VI Input Voltage Range (REF) 0.5 to +5.5 V 2 CLKA1 15 CLKA4 VI Input Voltage Range 0.5 to V (except REF) VDD+0.5 CLKA2 3 14 CLKA3 IIK (VI < 0) Input Clamp Current 50 mA VDD 4 13 VDD IO (VO = 0 to VDD) Continuous Output Current 50 mA 5 GND GND 12 VDD or GND Continuous Current 100 mA TA = 55C Maximum Power Dissipation 0.7 W 6 CLKB1 11 CLKB4 (3) (in still air) CLKB2 7 CLKB3 10 TSTG Storage Temperature Range 65 to +150 C S2 8 Operating Commercial Temperature 0 to +70 C 9 S1 Temperature Range Operating Industrial Temperature -40 to +85 C SOIC/ TSSOP Temperature Range TOP VIEW NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation APPLICATIONS: of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating SDRAM conditions for extended periods may affect reliability. Telecom 2. The input and output negative-voltage ratings may be exceeded if the input and output Datacom clamp-current ratings are observed. PC Motherboards/Workstations 3. The maximum package power dissipation is calculated using a junction temperature of 150C and a board trace length of 750 mils. Critical Path Delay Designs PIN DESCRIPTION Pin Name Pin Number Type Functional Description REF 1 I N Input reference clock, 5 Volt tolerant input (1) CLKA1 2 Out Output clock for bank A (1) CLKA2 3 Out Output clock for bank A VDD 4, 13 PWR 3.3V Supply GND 5, 12 GND Ground (1) CLKB1 6 Out Output clock for bank B (1) CLKB2 7 Out Output clock for bank B (2) S2 8 I N Select input Bit 2 (2) S1 9 I N Select input Bit 1 (1) CLKB3 10 Out Output clock for bank B (1) CLKB4 11 Out Output clock for bank B (1) CLKA3 14 Out Output clock for bank A (1) CLKA4 15 Out Output clock for bank A (1) CLKOUT 16 Out Output clock, internal feedback on this pin NOTES: 1. Weak pull down on all outputs. 2. Weak pull ups on these inputs. 2