DATASHEET HI-506, HI-507, HI-508, HI-509 FN3142 Rev 10.00 Single 16 and 8/Differential 8-Channel and 4-Channel CMOS Analog Multiplexers Jun 14, 2016 The HI-506/HI-507 and HI-508/HI-509 monolithic CMOS Features multiplexers each include an array of sixteen and eight Pb-Free Available (RoHS Compliant) (See Ordering Info) analog switches respectively, a digital decoder circuit for channel selection, voltage reference for logic thresholds, and Low ON Resistance 180 an enable input for device selection when several Wide Analog Signal Range 15V multiplexers are present. The Dielectric Isolation (DI) TTL/CMOS Compatible process used in fabrication of these devices eliminates the problem of latchup. DI also offers much lower substrate Access Time . 250ns leakage and parasitic capacitance than conventional junction Maximum Power Supply 44V isolated CMOS (see Application Note AN520). Break-Before-Make Switching The switching threshold for each digital input is established by an internal +5V reference, providing a guaranteed minimum No Latch-Up 2.4V for logic 1 and maximum 0.8V for logic 0. This allows Replaces DG506A/DG506AA and DG507A/DG507AA direct interface without pullup resistors to signals from most Replaces DG508A/DG508AA and DG509A/DG509AA logic families: CMOS, TTL, DTL and some PMOS. For protection against transient overvoltage, the digital inputs Applications include a series 200 resistor and diode clamp to each supply. Data Acquisition Systems The HI-506 is a single 16-channel, the HI-507 is an Precision Instrumentation 8-channel differential, the HI-508 is a single 8-channel and Demultiplexing the HI-509 is a 4-channel differential multiplexer. Selector Switch If input overvoltages are present, the HI-546/HI-547/HI-548/ HI-549 multiplexers are recommended. FN3142 Rev 10.00 Page 1 of 25 Jun 14, 2016HI-506, HI-507, HI-508, HI-509 Ordering Information TEMP. PART NUMBER PART MARKING RANGE (C) PACKAGE PKG. DWG. HI1-0506-2 HI1-506-2 -55 to +125 28 Ld CERDIP F28.6 HI4P0506-5Z (Note 1) HI4P 506-5Z 0 to +75 28 Ld PLCC (Pb-free) N28.45 HI9P0506-9Z (Note 1) HI9P506-9Z -40 to +85 28 Ld SOIC (Pb-free) M28.3 HI3-0507-5Z (No longer HI3-507-5Z 0 to +75 28 Ld PDIP (Note 3) (Pb-free) E28.6 available, recommended replacement: HI3-0547-5Z) HI1-0508-2 HI1-508-2 -55 to 125 16 Ld CERDIP F16.3 HI3-0508-5Z (Note 1) HI3-508-5Z 0 to +75 16 Ld PDIP (Note 3) (Pb-free) E16.3 HI9P0508-5Z (Notes 1, 2) HI9P508-5Z 0 to +75 16 Ld SOIC (Pb-free) M16.15 HI9P0508-9Z (Note 1) HI9P508-9Z -40 to +85 16 Ld SOIC (Pb-free) M16.15 HI1-0509-2 HI1-509-2 -55 to +125 16 Ld CERDIP F16.3 HI4P0509-5Z (Notes 1, 2) (No HI4P 509-5Z 0 to +75 20 Ld PLCC (Pb-free) N20.35 longer available, recommended replacement: DG409DYZ) NOTES: 1. These Intersil Pb-free plastic packaged products employ special Pb-free material sets molding compounds/die attach materials and 100% matte tin plate PLUS ANNEAL - e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 2. Add 96 suffix for tape and reel. Please refer to TB347 for details on reel specifications. 3. Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications. FN3142 Rev 10.00 Page 2 of 25 Jun 14, 2016