Users Manual RL78/G10 R20UT2349XJ0200 R20UT2349XJ0200 RL78/G10 Target board QB-R5F10Y16-TB Users Manual Rev 2.00 2013.06.24 QB-R5F10Y16-TB Rev 2.00 2013.06.24 The QB-R5F10Y16-TB is a target board used for evaluating microcontroller operations, using the E1, the Renesas Electronics E1 on-chip debug emulator with programming function (hereinafter referred to as E1). (1) RL78/G10 target board (QB-R5F10Y16-TB) features RL78/G10 (QB-R5F10Y16-TB) Incorporates RL78/G10 (R5F10Y16). RL78/G10(R5F10Y16) Equipped with universal area (2.54 mm pitch) (2.54mm ) Supports both flash memory programming and on-chip debugging (using TOOL0 pin) Highly extendable peripheral board connectors are equipped with microcontroller pins , (TOOL0 ) It can be used as a DIP conversion board of 2.54mm pitch by cutting off a board. Lead-free (Pb-free) product , 2.54 DIP (Pb) (2) hardware specifications CPU R5F10Y16 Main clock operating frequency MAX 20 MHz. CPU R5F10Y16 20MHz Embedded parts CN1, CN2, CN4: Peripheral board connectors (2.54 mm pitch), 5-pin socket 3 (pad only) CN1,CN2,CN4: (2.54mm ) 5pin x3() CN3: 14-pin connector (for E1 connection) CN3: 14pin (E1 ) Power LED: Red 1 (LED2) Power LED: x1(LED2) LED: Yellow 1 (LED1 connected to P00) LED: x1(LED1 P00 ) SW: SW1 (connected to INTP0) SW: SW1(INTP0 ) Operating voltage 2.7 to 5.5 V (When the high-speed on-chip oscillator used at 20MHz) 2.7V5.5V 20MHz (3) Dimensions and parts layout Cutting points LED LED upper:LED2(POWER) :LED2(POWER) :LED1(P00) lower:LED1(P00) <TopView> CN4 CN2 <TopView> CN4 CN2 1 10 1 10 POWER POWER 14pin connector TOOL0 Universal area TOOL0 VDD VDD 14pin P00 P00 RESET RESET T RESET T RESET GND GND VDD SW1 VDD SW1 SW1(INTP0) GND 5 GND 6 5 6 SW1(INTP0) QB-R5F10Y16 QB-R5F10Y16 SS-77226-1 SS-77226-1 CN1 RL78/G10 CN1 RL78/G10 <BottomView> <BottomView> GND GND JP1 VDD VDD JP1 GND GND JP2 JP2 T RESET T RESET JP4 JP4 RESET RESET JP3 JP3 TOOL0 TOOL0 RESET RESET VDD VDD 60mm 60mm Pattern on the board: Splitting this wiring leaves open the relevant circuit ( ). : To reconnect the circuit, short the circuit by soldering ( ). When using P00 cut off the short pad on the left side of LED. P00 LED Showing of the pad on circuit diagram. open: short: : : (4) Notes on use Renesas Electronics will not provide any support for this board, but the board can be exchanged with a new product only when it has an initial failure. Before cutting off a board by hand, please make a cut by using a cutter. It is also possible to cut off it by using nippers. , R20UT2349XJ0200 Rev.2.00 Page 1 of 3 R20UT2349XJ0200 Rev.2.00 Page 1 of 3 2013.06.24 2013.06.24 20mm OCD/Flash Program 20mm OCD/Flash Program Users Manual R20UT2349XJ0200 RL78/G10 RL78/G10 Target board R20UT2349XJ0200 QB-R5F10Y16-TB Users Manual Rev 2.00 2013.06.24 Rev 2.00 2013.06.24 QB-R5F10Y16-TB JP1JP4 JP1 JP4 - Setting of JP1, JP2, JP3 and JP4 are following. JP1 JP2 JP3 JP4 JP1 JP2 JP3 JP4 When using P125/KR1/RESET pin as RESET pin. (default) Short Short Open Short P125/KR1/RESET RESET () When using P125/KR1/RESET pin as P125 or KR1 pin. Open Open Short Open P125/KR1/RESET P125/KR1 - When using DIP conversion board of 2.54mm pitch by cutting off a board. 2.54mm DIP Please short of RESET pad. (default open) RESET() 7.62mm 7.62mm 10.12mm 10.12mm 1 10 1 1 10 VDD 10 1 VDD 10 RESET Please short of RESET pad. RESET 2.54mm 2.54mm 6 6 6 5 GND 5 6 5 GND 5 <Bottom View> <Top View> <Top View> <Bottom View> - When using DIP conversion board of 2.54mm pitch by cutting off a board. OCD/ Please connect CN1 and CN4 as following. CN1 CN4 Please short of RESET pad. CN4 CN1 10 1 VDD 1 10 CN4 CN1 TOOL0 <BottomView> 10 1 VDD 1 10 RESET RESET TOOL0 <BottomView> T RESET RESET RESET GND T RESET VDD GND 6 6 5 GND 5 VDD 6 6 5 GND 5 P125/KR1/RESET - RESET RESET () Please connect the following circuit according to use the P125/KR1/RESET pin. - When using RESET pin. - P125/KR1 Connect the external reset circuit. (Possible to be open) P125/KR1 - When using P125 or KR1 pin. Connect the circuit the P125/KR1. R20UT2349XJ0200 Rev.2.00 Page 2 of 3 R20UT2349XJ0200 Rev.2.00 Page 2 of 3 2013.06.24 2013.06.24 OCD/Flash Program 20.00mm OCD/Flash Program 20.00mm