BH18RB1WGUT-E2 ROHM

CMOS LDO Regulators for Portable Equipments 1ch 150mA CMOS LDO Regulators No.11020ECT03 BHRB1WGUT series Description The BHRB1WGUT series is a line of 150 mA output CMOS regulators that deliver a highly stable precision ( 1%) output voltage. Proprietary ROHM technology enables a small load regulation of 2 mV and a dropout voltage of 100 mV. At just 1.0 mm 1.04 mm, the new VCSP60N1 package is extremely compact, and the IC s enhanced protection circuits contribute to improved end products characteristics. Features 1) High accuracy output voltage: 1% 2) Dropout voltage: 100 mV (at 100 mA) 3) Stable with ceramic capacitors 4) Low bias current: 34 A 5) High ripple rejection ratio: 63 dB (Typ., 1 kHz) 6) Output voltage on/off control 7) Built-in overcurrent and thermal shutdown circuits 8) VCSP60N1 WL-CSP package : (1.01.040.6mm) Applications Battery-driven portable devices, etc. Product line 150 mA BHRB1WGUT Series Product name 1.5 1.8 2.5 2.8 2.9 3.0 3.1 3.3 Package BHRB1WGUT VCSP60N1 Model name: BHRB1W a b Symbol Description Output voltage specification Output voltage (V) Output voltage (V) 15 1.5 V (Typ.) 29 2.9 V (Typ.) a 18 1.8 V (Typ.) 30 3.0 V (Typ.) 25 2.5 V (Typ.) 31 3.1 V (Typ.) 28 2.8 V (Typ.) 33 3.3 V (Typ.) b Package GUT: VCSP60N1 www.rohm.com 2011.01 - Rev.C 1/8 2011 ROHM Co., Ltd. All rights reserved. Technical Note BHRB1WGUT series Absolute maximum ratings Parameter Symbol Ratings Unit VMAX -0.3 to +6.5 V Applied supply voltage *1 Pd 530 mW Power dissipation Topr -40 to +85 C Operating temperature range Storage temperature range Tstg -55 to +125 C *1: Reduce by 5.3 mW/C over 25C, when mounted on a glass epoxy PCB (7 mm 7 mm 0.8 mm). Recommended operating ranges (not to exceed Pd) Parameter Symbol Ratings Unit Power supply voltage VIN 2.5 to 5.5 V IOUT 0 to 150 mA Output current Recommended operating conditions Ratings Symbol Unit Parameter Conditions Min. Typ. Max. The use of ceramic capacitors is *2 Input capacitor CIN 0.7 1.0 F recommended. The use of ceramic capacitors is *2 Output capacitor CO 0.7 1.0 F recommended. *2: Make sure that the output capacitor value is not kept lower than this specified level across a variety of temperature, DC bias characteristic. And also make sure that the capacitor value cannot change as time progresses. Electrical characteristics *5 (Unless otherwise specified, Ta = 25C, VIN = VOUT + 1.0 V , STBY = 1.5 V, CIN = 1 F, CO = 1 F) Limits Parameter Symbol Unit Conditions Min. Typ. Max. OUT VOUT IOUT = 1 mA, Ta = 25C, V 0.99 1.01 BH25RB1WGUT or higher Output voltage 1 VOUT1 VOUT V VOUT VOUT IOUT = 1mA, Ta = 25C, - 25 mV + 25 mV BH15, 18RB1WGUT VOUT VOUT IOUT = 1 mA Output voltage 2 VOUT2 VOUT V *3 0.97 1.03 Ta = -40C to 85C IOUT = 0 mA Circuit current IGND 34 72 A *3 Ta = -40C to 85C Circuit current (STBY) ICCST 1.0 A STBY = 0 V VRR = -20 dBV, fRR = 1 kHz, Ripple rejection ratio RR 63 dB IOUT = 10 mA VIN = 0.98 VOUT, IOUT = 100 mA Dropout voltage VSAT 100 150 mV (Excluding BH15, 18RB1WGUT) IOUT = 10 mA Line regulation VDLI 2 20 mV *4 VIN = VOUT + 0.5 V to 5.5 V Load regulation VDLO 2 30 mV IOUT = 1 mA to 100 mA Overcurrent protection limit current ILMAX 300 mA VO = VOUT 0.98 Short current ISHORT 40 mA VO = 0 V *3 STBY pin current ISTBY 0.5 1.3 3.6 A Ta = -40C to 85C *3 ON VSTBH 1.2 VIN V Ta = -40C to 85C STBY control voltage *3 OFF VSTBL -0.2 0.2 V Ta = -40C to 85C * This IC is not designed to be radiation-resistant. *3: These specifications are guaranteed by design. *4: For BH15, 18RB1WGUT, VIN = 3.0 V to 5.5 V. *5: For BH15, 18RB1WGUT, VIN = 3.5 V. www.rohm.com 2011.01 - Rev.C 2/8 2011 ROHM Co., Ltd. All rights reserved.