High power low ohmic chip resistors Wide terminal type LTR series Datasheet Features 1)Chip Resistors for current detection : 10m ~ 2)High joint reliability with long side terminations. 3)Improvement of rated power enables to displace smaller size of resistors,and it contributes space savings in your set. 4)ROHM resistors have obtained ISO9001 / ISO / TS16949 certification. 5)Corresponds to AEC-Q200. Products list Rated Operating Size Resistance Temperature power Resistance range temperature Part No. tolerance coefficient (70) range (mm) (inch) (W) (%) (ppm / ) () () F ( 1% ) 150 0.047R<0.100 (E24 series) LTR10 2012 0805 0.5 -55 +155 J ( 5% ) (E24 series) 150 0.100R<10 (E24 series) 0300 0.010R0.020 (E24 series) 0200 0.020R0.050 F ( 1% ) LTR18 3216 1206 1.0 -55 +155 J ( 5% ) (E24 series) 0150 0.050R0.500 (E24 series) 100 0.500R1.000 F ( 1% ) (E24 series) 0+150 0.100R<0.200 LTR100 6432 2512 2.0 F ( 1% ) 0+100 0.200R<1 (E24 series) -55 +155 J ( 5% ) 200 0.100R<1 (E24 series) Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with the product before using or ordering it. Part number description L T R 1 0 E V H J J 1 R 0 Resistance Special Part No. Size (mm inch ) Packaging specifications code Nominal resistance tolerance part code Resistance code, 3 or 4 digits. 10(2012 0805 ) Packaging Quantity Part No. Code F (1%) U 10m LTR specifications / Reel 18(3216 1206 ) Resistance J (5%) S 11m (High power 100(6432 2512 ) Paper tape tolerance Resistance 91m chip resistors LTR10 EVH 5000 + code (4mm Pitch) L 100m Wide terminal Special code Paper tape type) LTR18 EZP 5,000 (4mm Pitch) FU, FS 4 digits FL, JS Embossed tape LTR100 JZP 4,000 JU, JL 3 digits (4mm Pitch) www.rohm.com 1/4 2016 ROHM Co., Ltd. All rights reserved. 2017.06 - Rev.FLTR series -low ohmic- Datasheet Chip resistor dimensions and markings LTR10 LTR 18 / 100 <Marking method> There are three or four digits used for the calculation number according to IEC code and Ris used for the decimal point. Example : 4digits62m=R062, 100m=R100 3digits100m=R10, 1=1R0 (Unit:mm) Marking Part No. (mm) (inch) L W t a b existence LTR10 2012 0805 1.20.10 2.00.10 0.550.10 0.300.20 0.350.20 Yes LTR18 3216 1206 1.60.10 3.20.10 0.580.10 0.500.20 0.500.20 No No LTR100 6432 2512 3.20.15 6.40.15 0.550.15 0.400.25 1.130.25 Land pattern example (Unit:mm) Dimensions A B C D Part No. LTR10 0.50 1.98 2.20 0.74 LTR18 0.55 2.90 3.20 1.18 LTR100 0.83 3.69 6.40 1.43 www.rohm.com 2/4 2016 ROHM Co., Ltd. All rights reserved. 2017.06 - Rev.F