CENB1030 Universal 30 Watt Series ITE Switch-Mode Power Supply 3 Year Warranty 100-240VAC Universal Input Meets EISA2007, CEC Efficiency Level V, EU (EC) No 278/2009 Phase II nd Certified to UL/EN60950-1, 2 Edition 5Vto 48V outputs, up to 32W Modified and Custom Designs Available Regulated Output with Low Ripple Impact-Resistant Polycarbonate Enclosure No load Power Consumption <0.3W Limited Power Source Desktop & Wall Plug Styles RoHS LPS Specifications All Specifications are typical at nominal input, full load at 25 C unless otherwise stated. MTBF >100,000 hours calculated AC Input 100-240VAC, -/-10%, 47-63 Hz, 1 Input Current 100VAC: 0.9A Hold-up Time 18 ms min. 115VAC, 60 msec 230VAC Inrush Current 60A peak, 264Vac, cold start Turn-on Time 2 seconds, max. Input Fuse 3.15A Internal Primary Current Fuse is provided Topology Switching Fixed Frequency Flyback Efficiency Meets EISA2007, CEC Efficiency Level V, Overload Protection Hiccup Mode and EU(EC) No. 278/2009 Phase II requirements Output Voltage See chart Short Circuit Protection Hiccup Mode Output Power See chart EMC See chart below Ripple and Noise 1% pk-pk max., 20MHz BW Safety Standards EN/IEC/CSA/UL60950-1, 2nd Edition, LPS Line & Load Voltage Regulation Line: +/- 1%, Load: +/-5% Dielectric Withstand Input-Output: 4,242VDC, Input-GND: 1,500 Vac, Output-GND: 500Vdc Transient Response 500s max., 50% load step, typical Operating Temperature 0 to 40C, no derating Minimum Load Not required Storage Temperature -40 to +85C Case Material: Black 94V0 Polycarbonate Relative Humidity 5% to 95%, non-condensing Case Dimensions: 95 x 54 x 31mm. See outline drawing Altitude 0 to 10,000 ft Weight = 200g Output Connector: 2.5mm barrel type (Ault 3) connector, Output Cable: 5V 9V models: 18AWG (SPT-1), 1,500mm, 2 conductor center contact (+). Other options available 12V 48V models: 18AWG (UL1185), 1,500mm, 2 conductor EMC Specifications Conducted Emissions EN55022 Class B, FCC Part 15, Class B. Radiated Emissions EN55022 Class B, FCC Part 15, Class B. Line Frequency Harmonics EN61000-3-2, Class A Voltage Fluctuations/Flicker EN61000-3-3 Static Discharge Immunity EN61000-4-2, 6kV Contact Discharge, 8kV air discharge Radiated RF Immunity EN61000-4-3, 3V/m. EFT/Burst Immunity EN61000-4-4, 2kV/5kHz. Line Surge Immunity EN61000-4-5, 1kV differential, 2kV common-mode Conducted RF Immunity EN61000-4-6, 3Vrms Power Frequency Magnetic Field Immunity EN61000-4-8, 3A/m Voltage Dip Immunity EN61000-4-11, Criteria B 1 of 2 SL Power Electronics Corp 6050 King Drive Ventura, CA 93003 Phone 805.486.4565 Fax 858.712.2040 Email: info slpower.com www.slpower.comCENB1030 Universal 30 Watt Series ITE Switch Mode Power Supply 3 Year Warranty Model Number Volts (V) Output Current (max) Max Watts Ripple (Vp-p max) CENB1030A0503F01 5 V 4.00 A 20.0 W 50 mV CENB1030A0703F01 7.5 V 3.00 A 22.5 W 75 mV CENB1030A0903F01 9 V 3.00 A 27.0 W 90 mV CENB1030A1203F01 12 V 2.50 A 30.0 W 120 mV CENB1030A1403F01 14 V 2.10 A 29.4 W 140 mV CENB1030A1503F01 15 V 2.00 A 30.0 W 150 mV CENB1030A1803F01 18 V 1.67 A 30.0 W 180 mV CENB1030A2403F01 24 V 1.33 A 31.9 W 240 mV CENB1030A4803F01 48 V 0.67 A 32.1 W 480 mV Notes: Part numbers above include 3 output connector and IEC320 C14 grounded input receptacle. See below for other options. Model Number Key CENB 1 030 A VV 03 F 01 Model01 = Standard.02 and higher indicates a modified model. Input Connector: = IEC320 C14 grounded, Other options available, see below Output Connector:03 = 2.5mm Barrel Type Connector. Other options available, contact factory. Output Voltage:05 = 5Vdc,12 = 12Vdc,24 = 24Vdc, etc. Model = Original Configuration Output Power:030 = 30 Watts of Outputs1 = Single Output Product Family: = Commercial/ITE/Industrial, = External,N = Model Series Designator AC Input Receptacle Options Output Connector Desktop Wall-Plug IEC320 - C14 IEC320 - C18 IEC320 - C8 N. America N. America Europe United Australia Class I Class II Class II Japan Japan Kingdom Grounded Ungro undedShave Interchangable Fixed Fixed Fixed Fixed (F) (Q) (N) (C) (B) (M) (G) (H) Notes: 1. For desktop options, choose applicable letter above. Notes: 1. Ault 3 Connector, center contact (+). 2. For Wall-Plug options, choose the applicable letter above and the unit will be fitted with 2. Connector is Switchcraft 760 plug or equivalent. the receptacle chosen. The N. A. blade version (C) will be an interchangeable blade. Mating connector is Switchcraft 712A or equivalent. The other options (B), (M), (G), and (H) will be fixed blades molded in the case. 3. Other connector options are available. Contact your local 3. Blade Kit is available which will include one each of a EU, UK, and Australian blade. Kit part SL Power Representative for details. is KT1027K. These can be used with the (C) version, to allow blades to be changed. Outline Drawings DATE CODE Desktop Style Wall-plug Style C Option Shown (with KT1027K interchangeable blade kit) Data Sheet 2014 SL Power Electronics Corp. The information and specifications contained herein are believed to be correct at the time of publication. Rev. 9-22-14 However, SL Power accepts no responsibility for consequences arising from reproduction errors or inaccuracies. Specifications are subject to change without notice. 2 of 2 SL Power Electronics Corp 6050 King Drive Ventura, CA 93003 Phone 805.486.4565 Fax 858.712.2040 Email: info slpower.com www.slpower.com