MINT1110A 110W Single Output Series Medical Universal Input Power Supply 2 Year Warranty 110W Convection Cooled AC-DC Power Supply Universal Input 90-264 VAC Less than 1.27 Height Rugged EMC Compliant Design 3 x 5 Package Approved to EN/IEC/UL60601-1 for Medical Compliant (LVD, RoHS) Specifications All Specifications are typical at nominal input, full load at 25C unless otherwise stated. AC Input Turn On Time 100-240VAC +/- 10%, 47-63 Hz single phase. Less than 2 seconds under all rated load conditions. Input Current Hold-up Time 115VAC: 1.4A. 16 ms at 110W, nominal input (120VAC). Inrush Current Overvoltage Protection The inrush at 264VAC, at a cold start, will not exceed 40A. See chart for levels, latching type Input Fuses Overload Protection F1, F2: 2.5A, 250VAC fuses provided on all models. Hiccup Mode Power Factor Short Circuit Protection Complies with EN61000-3-2. Hiccup Mode Efficiency Overtemperature Protection 87% typical. Provided on all models. Output Power Medical Safety Standards 90 - 110W continuous. EN/IEC/UL 60601-1, CSA22.2, No. 601.1 Ripple and Noise Isolation 1% pk-pk max., 20MHz BW, differential mode. Measured with noise Input-Output: 4000VAC, Input-Ground: 1500VAC, Output-Ground: probe directly across output terminals. 500VDC Output Voltage Earth Leakage Current See chart. <130A at 264Vac, 60Hz. Minimum Load Operating Temperature Not required. 0 to 70C (derate from full rated power above 40C) Total Regulation Output Power Derating See chart. Derate Output Power by 2.5% per C above 40C, up to 70C max. Transient Response Storage Temperature 500s max., 50% load step, typical. -40 to +85C. Relative Humidity 5% to 95%, non-condensing 1 of 3 SL Power Electronics Corp 6050 King Drive Ventura, CA 93003 Phone 805.486.4565 Fax 858.712.2040 Email: info slpower.com www.slpower.com MINT1110A 110W Single Output Series Medical Universal Input Power Supply 2 Year Warranty Output Parameters Model Output Ripple Total OVP Initial Setpoint Number Volts (V) Current & Noise Regulation Threshold Tolerance MINT1110A1208K01 12V 7.5A 120mV 2% 15.0 1V 1% MINT1110A1508K01 15V 6.5A 150mV 2% 18.0 1V 1% MINT1110A1808K01 18V 5.8A 180mV 2% 23.0 1V 1% MINT1110A2408K01 24V 4.6A 240mV 2% 28.0 1V 1% Specifications (continued) Vibration Shock 2 Operating: 0.003 g /Hz, 1.5 g overall, 3 axes, 10 min. / axis Operating: Half-sine, 20 g , 10 ms, 3 axes, 6 shocks total rms pk 2 Non-Operating: 0.026 g /Hz, 5.0 g overall, 3 axes, 1 hr. / axis Non-Operating: Half-sine, 40 g , 10 ms, 3 axes, 6 shocks total rms pk Enclosure Dimensions Operating Altitude See outline drawing. -500 to 10,000 ft. Weight Non-operating Altitude 372 grams -500 to 40,000 ft. EMI/EMC Compliance Conducted Emissions EN55011 Class B, FCC Part 15, Class B. Static Discharge Immunity EN61000-4-2, 6kV Contact Discharge, 8kV air discharge Radiated RF Immunity EN61000-4-3, 10V/m. EFT/Burst Immunity EN61000-4-4, 2kV/5kHz.. Line Surge Immunity EN61000-4-5, 1kV differential, 2kV common-mode Conducted RF Immunity EN61000-4-6, 3Vrms Power Frequency Magnetic Field Immunity EN61000-4-8, 3A/m Voltage Dip Immunity EN61000-4-11 240VAC, 0%/0.5 cycle, 40%/5cycles, 70%/25 cycles Line Frequency Harmonics EN61000-3-2, Class A Model Number Key MINT 1 110 A 12 08 K 01 01 = Standard Configuration. 02 and higher indicate modified model. Input Connector Output Connector Output Voltage Model Configuration Output Power (Watts) of Outputs Product Family: = Medical, = Internal,N = New Technology 2 of 3 SL Power Electronics Corp 6050 King Drive Ventura, CA 93003 Phone 805.486.4565 Fax 858.712.2040 Email: info slpower.com www.slpower.com