STEVAL-IPMNM5Q Data brief 450 W motor control power board based on STIPQ5M60T-H SLLIMM-nano 2nd series MOSFET IPM Features Input voltage: from 125 to 400 V DC Nominal power: up to 450 W Allowable maximum power is related to the application conditions and cooling system Nominal current: up to 1.8 Arms Input auxiliary voltage: up to 20 VDC Single- or three-shunt resistors for current sensing (with sensing network) Three options for current sensing: dedicated external op-amps, internal SLLIMM-nano op-amp (single) or via MCU Overcurrent hardware protection IPM temperature monitoring and protection Hall sensor or encoder input MOSFETs intelligent power module: SLLIMM-nano 2nd series IPM (STIPQ5M60T-H) - Full molded package Motor control connector (32 pins) interfacing with ST MCU boards Universal design for further evaluation with breadboard and testing pins Very compact size WEEE compliant RoHS compliant Product summary Description 450 W motor control power board The STEVAL-IPMNM5Q is a compact motor drive power board equipped with based on SLLIMM-nano (small low-loss intelligent molded module) 2nd series based on N- STIPQ5M60T-H STEVAL-IPMNM5Q channel Power MOSFET MDmesh DM2 fast-recovery diode (STIPQ5M60T-H). It SLLIMM-nano 2nd series provides an affordable and easy-to-use solution for driving high power motors in a MOSFET IPM wide range of applications such as power white goods, air conditioning, compressors, power fans and 3-phase inverters for motor drives in general. SLLIMM-nano 2nd series IPM, 3-phase The IPM consists of six MOSFETs, three high voltage half-bridge gate driver ICs and STIPQ5M60T-HZ/ inverter, 5 A, 1.0 a wide range of features like undervoltage lockout, smart shutdown, internal Ohm max., 600 V STIPQ5M60T-HL temperature sensor and NTC, overcurrent protection and internal op-amp. N-channel MDmesh DM2 The main characteristics of this evaluation board are small size, minimal BOM and high efficiency. It features an interface circuit (BUS and V connectors), bootstrap CC Featured STPOWER capacitors, snubber capacitor, hardware short-circuit protection, fault event signal technologies SLLIMM and temperature monitoring. It is designed to work in single- or three-shunt STM32 MCSDK configuration and with three current sensing options: three dedicated on-board op- Development STSW- amps, op-amps available on a connected microcontroller, or the single op-amp environments POWERSTUDIO embedded in the power module. A Hall/Encoder section completes the circuit. PMSM / BLDC The system is designed to achieve accurate and fast conditioning of current feedback Motor to satisfy the typical requirements for field oriented control (FOC). Applications 3-phase Induction The STEVAL-IPMNM5Q is compatible with ST control boards based on STM32 Motor (ACIM) microcontrollers, providing a complete platform for motor control. DB4138 - Rev 1 - April 2020 www.st.com For further information contact your local STMicroelectronics sales office.STEVAL-IPMNM5Q Schematic diagrams DB4138 - Rev 1 page 2/8 1 Schematics Figure 1. STEVAL-IPMNM5Q board schematic (1 of 5) Input DC bus voltage +Bus 3.3V R1 R5 470K U1D 1k0 3.3V J1 12 + C1 R2 D1 14 1 1.65V 13 + 470K - 2 TSV994 INPUT-dc 330u/400V + C3 R6 + C4 47u/35V 47u/35V 1k0 Bus voltage R3 120R R4 C2 10n 7k5 STEVAL-IPMNntmp decoder G M t 0 RC1 0 RC2 0 1 2 3 4 RC3 RC4 0 0 RC5 RC7 0 0 RC6 0 m 5 6 7 8 9 RC9 RC10 RC11 RC12 0 RC8 0 0 0 0 N Q 0 RC13 RC14 p 0 11 4