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igure 1 20> .< *7- PROCRIMPER III Hand Tool Assembly 586301 The tool features a tool frame with a stationary jaw consists of Die Assembly 586302 and and handle, a moving jaw, a moving handle, and an PROCRIMPER III Hand Tool Frame 3549401. The adjustable ratchet that ensures full crimping. The tool tool is used to crimp the receptacles onto the wire frame holds a die assembly with two crimping sizes listed in Figure 1. Read these instructions chambers. thoroughly before crimping any receptacles. The die assembly features an anvil die and a crimper die. Die retaining pins and die retaining screws are used to position and secure the dies in the tool frame. % % % %12<,87= 855.--8,>6.7=2<<>+3.,==8,1*70. %B,8 5.,= 872,< 8 98 *=287 * 2<+> 0 8/ 55 7=. 7*=287*5 201=< .<- & % % 8 5*=.<= . 2<287*7- .0287*5 ><=86 2,. % 5808*7-%B,8 5.,= 872,<* .= *-.6* 4< 2<2=8> .+<2=.*=333 24/),)20/.+1 /- % *-.6* 4 =1. 9 8->,=< 5808< *7-,869*7B7*6.<><.-* .=1.9 89. =B8/=1.2 .<9.,=2 .8 7. < (( % ) % % ( * % % Figure 2 & . * % () % *&& ( * * 1. Open the tool handles and remove the two die ) &+ %) * )) % &% retaining screws from the tool jaws. % &% *&, . 2. Place the anvil die in the moving jaw of the tool ( *. &( +% * *&& frame. The rear crimping chamber is used to crimp the receptaclemake sure that the wire anvil is Refer to Figure 1 and select wire of the specified size. positioned so that the applicable wire size marking Strip the wire to the length indicated, taking care not on the die is located at the inside of the frame. to nick or cut wire strands. Select an applicable receptacle and identify the appropriate crimping % )( , ( *& & & * ( chamber according to the wire size markings on the / &( anvil die. Refer to Figure 3 and proceed as follows: 1. Squeeze tool handles together until the ratchet releases and then allow the tool jaws to open fully. 3. Insert die retaining screw and two die retaining pins through the jaw and into the die. Tighten the 2. Insert the receptacle (mating end first) into the screw just enough to hold the die in place. Do not BACK of the tool in the rear crimping chamber so tighten the screw completely at this time. that the flat side of the receptacle faces the anvil die. Make sure that the wire barrel is centered in 4. Place the crimper die in the stationary jaw of the the crimping chamber. tool frame. Make sure that the chamfered edge of the die faces outward. 3. Hold the receptacle in position and squeeze the tool handles together until ratchet engages 5. Insert die retaining screw and two die retaining sufficiently to hold the receptacle in position. Do pins through the jaw and into the die. Tighten the NOT deform the wire barrel. screw just enough to hold the die in place. Do not tighten the screw completely at this time. 4. Insert the stripped wire into the wire barrel of the receptacle. 6. Carefully close the tool handles, making sure that the anvil and crimper dies align properly. 5. Holding the wire in place, squeeze tool handles Continue closing the tool handles until the tool together until ratchet releases. Allow tool handles frame ratchet has engaged sufficiently to hold the to open and remove crimped receptacle. dies in place, then tighten both die retaining 6. Inspect the crimped receptacle to ensure that screws. the crimp is centered on the wire barrel and the 7. To disassemble, open the tool handles, remove wire is fully inserted. Check the receptacle crimp the two die retaining screws and four die retaining height as described in Section 5. If necessary, pins, and slide the dies out of the tool jaws. adjust the crimp height as described in Section 6. ) % %