CA10 ProBus Current Adapter Key Features The CA10 is a programmable and customizable interface device that Provides ability for third party seamlessly incorporates third party current transducers/transformers current sensor to operate like a with Teledyne LeCroy oscilloscopes or motor drive analyzers. The easy Teledyne LeCroy probe to use interface provides the ability for the CA10 to be programmed to contain the specifications of the current sensor allowing it to Programmable EEPROM for saving third party current sensor automatically correct for the gain or attenuation and display results in parameters Ampere units. This allows the third party device to be recognized and Allows for addition of shunt operate as if it were a Teledyne LeCroy probe. resistor and RLC filter components Measurement Flexibility Power of Customization ProBus Activ e interface with The CA10 ProBus Current Adapter The CA10 provides the ability to easily automatic scaling in A/div provides complete flexibility in install physical hardware components current measurements by allowing such as shunt resistors and bandwidth Easy to use, saves time and a wide variety of third party current filter components based on the possible errors transducers and transformers to be requirements of the device being used. easily incorporated with a Teledyne The CA10 also has programmable LeCroy oscilloscope or motor drive bandwidth limit filters of full BW, analyzer. Examples of devices that can 200 MHz, or 20 MHz. be used with the CA10 include Pearson Easy to Use Current Transformers, Danisense/ The programmable interface is intuitive LEM Current Transducers, PEM-UK and easy to use. Once the CA10 is Rogowksi Coils, or any conventional configured, it will recognize the third turns-ratio current transformers. Once party device with the correct scaling the CA10 is programmed, the third factors on any compatible Teledyne party transducer/transformer will be LeCroy oscilloscope or motor drive recognized and operate like a Teledyne analyzer. This saves time and possible LeCroy probe. errors involved in manually entering scaling factors each time the device is connected. SPECIFICATIONS AND ORDERING INFORMATION Customizing the CA10 L1 J3 J2 It is possible to customize the CA10 0 ohm 1 1 through the addition of shunt resistors and other bandwidth filtering components. 2 3 3 2 C8 C7 R13 R14 R4 A schematic of the user-installable components is shown here. The CA10 Transformer/ MDA/Oscilloscope Transducer Input BNC comes from the factory with a 0 (short) Connector Connector Customizable Circuit installed in the L1 location, and no components in the other locations shown. CAUTION: The secondary of a current transformer (CT), when unterminated, can generate hazardous open circuit voltages when energized. These voltages could be dangerous to personnel and damage the oscilloscope. If the CA10 is used with an unterminated current transformer, you must install a suitably rated terminating resistor in the CA10 before energizing the CT. Download the CA10 ProBus Current Adapter Operators Manual from teledynelecroy.com for customization instructions. Specifications Input Coupling DC, AC, Both Input Termination 1M or 50 Programmable Bandwidth Filters Full, 200 MHz, 20 MHz Transformer/Transducer Interface BNC Scaling Factors Programmable Resistive Termination (if required) Customizable (see Customizing the CA10 figure above) Oscilloscope Interface Teledyne LeCroy ProBus Note: Some third party devices will require a separate power supply or batteries. The CA10 does not have the ability to supply the power to these devices. Ordering Information CA10 ProBus current adapter attached to a Danisense Current Product Description Product Code Transducer. Also shown is a Pearson Current Transformer and a ProBus Current Adapter CA10 PEM-UK Rogowski Coil, which are also third party devices that can Set of 4 CA10, ProBus Current Adapter CA10-QUADPAK be used with the CA10. Included with Standard Configuration CA10 Compatibility* Description Qty CA10 ProBus Current Adapter 1 HDO4000 HDO6000 Heat-Shrink tubing (6 length) 1 HDO8000 Removable Labels (sheet of 20) 1 MDA800 WaveRunner 6 Zi Included with Standard Configuration CA10-QUADPAK WaveRunner HRO 6Zi Description Qty WavePro 7Zi/Zi-A CA10 ProBus Current Adapter 4 WaveMaster 8 Zi/Zi-A/Zi-B Carrying Case 1 LabMaster 9 Zi-A Heat-Shrink tubing (24 length) 1 Removable Labels (sheet of 20) * The CA10 requires the Teledyne LeCroy oscilloscope to be running 4 firmware version 7.8.x or greater. Customer Service Teledyne LeCroy oscilloscopes and probes are designed, built, and tested to ensure high reliability. In the unlikely event you experience difficulties, our digital oscilloscopes are fully warranted for three years and our probes are warranted for one year. This warranty includes: No charge for return shipping Long-term 7-year support Upgrade to latest software at no charge 1-800-5-LeCroy Local sales offices are located throughout the world. teledynelecroy.com Visit our website to nd fi the most convenient location. ca10-ds-24jun15 2015 Teledyne LeCroy, Inc. All rights reserved. Specifications, prices, availability, and delivery subject to change without notice. Product or brand names are trademarks or requested trademarks of their respective holders.