CRS01 TOSHIBA Schottky Barrier Rectifier Schottky Barrier Type CRS01 High Speed Rectifier Applications Unit: mm Low forward voltage: V = 0.37 V I = 0.7 A FM FM Average forward current: I = 1.0 A F (AV) Repetitive peak reverse voltage: V = 30 V RRM Suitable for compact assembly due to small surface-mount package TM SFLAT (Toshiba package name) Absolute Maximum Ratings (Ta = 25C) Characteristics Symbol Rating Unit Repetitive peak reverse voltage V 30 V RRM Average forward current I 1.0 (Note 1) A F(AV) 20 (50 Hz) Peak one cycle surge forward current I A FSM (non-repetitive) 22 (60 Hz) Junction temperature T 40~125 C j JEDEC Storage temperature T 40~150 C stg JEITA Note 1: T = 98C: Rectangular waveform ( = 180), V = 15 V R TOSHIBA 3-2A1A Note 2: Using continuously under heavy loads (e.g. the application of Weight: 0.013 g (typ.) high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (Handling Precautions/Derating Concept and Methods) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Electrical Characteristics (Ta = 25C) Characteristics Symbol Test Condition Typ. Max Unit V I = 0.1 A 0.25 FM (1) FM Peak forward voltage V I = 0.7 A 0.33 0.37 V FM (2) FM V I = 1.0 A 0.36 FM (3) FM Repetitive peak reverse current I V = 30 V 1.5 mA RRM RRM Junction capacitance C V = 10 V, f = 1.0 MHz 40.0 pF j R Device mounted on a ceramic board 70 (soldering land: 2 mm 2 mm) Thermal resistance (junction to ambient) R C/W th (j-a) Device mounted on a glass-epoxy board 140 (soldering land: 6 mm 6 mm) Thermal resistance (junction to lead) R 20 C/W th (j-) 1 2006-11-13 CRS01 Marking Abbreviation Code Part No. S1 CRS01 Standard Soldering Pad Unit: mm 1.2 1.2 2.8 Handling Precaution Schottky barrier diodes have reverse current characteristic compared to the other diodes. There is a possibility SBD may cause thermal runaway when it is used under high temperature or high voltage. This device is V -I trade-off type, lower V higher I therefore, thermal runaway might occur when F RRM F RRM voltage is applied. Please take forward and reverse loss into consideration during design. The absolute maximum ratings denote the absolute maximum ratings, which are rated values and must not be exceeded during operation, even for an instant. The following are the general derating methods that we recommend when you design a circuit with a device. V : Use this rating with reference to the above. V has a temperature coefficient of 0.1%/C. Take RRM RRM this temperature coefficient into account designing a device at low temperature. I : We recommend that the worst case current be no greater than 80% of the absolute maximum rating F(AV) of I and T be below 100C. When using this device, take the margin into consideration by F(AV) j using an allowable Ta max - I curve. F(AV) I : This rating specifies the non-repetitive peak current. This is only applied for an abnormal operation, FSM which seldom occurs during the lifespan of the device. T : Derate this rating when using a device in order to ensure high reliability. We recommend that the j device be used at a T of below 100C. j Thermal resistance between junction and ambient fluctuates depending on the devices mounting condition. When using a device, please design a circuit board and a soldering land size to match the appropriate thermal resistance value. Please refer to the Rectifiers Databook for further information. 2 2006-11-13