TLP116A TOSHIBA PHOTOCOUPLER IRED & PHOTO-IC TLP116A Plasma Display Panels (PDPs) Unit: mm High-Speed Interface Factory Automation (FA) 6 5 4 The Toshiba TLP116A mini-flat coupler is a small-outline coupler suitable for surface-mount assembly. The TLP116A consists of an infrared LED and an integrated high-gain, high-speed photodetector. This unit is housed in the 6-pin SO package and guarantees a creepage distance of 5.0mm, a clearance of 5.0mm and an insulation thickness of 0.4mm. Therefore, the TLP116A 1 3 meets the reinforced insulation class requirements of international safety 3.7 0.15 7.0 0.4 standards. Inverter logic (totem-pole output) 0.4 0.5 min 1.27 SO6 package 2.54 Guaranteed performance over: 40 to 100C Power supply voltage: 4.5 to 5.5V TOSHIBA 11 4L1 Input thresholds current: I = 5 mA (max) Weight: 0.08 g (typ.) FHL Propagation delay time (tpHL / tpLH): 60 ns (max) Pin Configuration (Top View) Switching speed: 20 MBd (typ.) 1: ANODE 1 VCC 6 Common-mode transient immunity: 10 kV/s 3: CATHODE Isolation voltage: 3750 Vrms 5 4: GND UL-recognized: UL 1577, File No.E67349 5: VO (Output) GND 3 4 6: VCC cUL-recognized: CSA Component Acceptance Service No.5A SHIELD File No.E67349 CQC-approved: GB4943.1,GB8898 Japan and Thailand Factory 2000m VDE-approved: EN 60747-5-5 , EN 62368-1 (Note 1) Schematic Note 1 : When a VDE approved type is needed, I CC V CC please designate the Option(V4). 6 I F Tr1 1 Truth Table I O VF Input LED Tr1 Tr2 Output V O 3 Tr2 5 H ON OFF ON L L OFF ON OFF H GND 4 SHIELD Construction Mechanical Rating A bypass capacitor of 0.1F must be Creepage Distance: 5.0mm (min) connected between pins 6 and 4. Clearance: 5.0mm (min) Insulation Thickness: 0.4mm (min) Start of commercial production 2008-07 2019 1 2019-10-10 Toshiba Electronic Devices & Storage Corporation 4.55 0.15 2.1 0.1 0.1 0.15 TLP116A Absolute Maximum Ratings (Ta=25C) Characteristic Symbol Rating Unit Forward current I 20 mA F Forward current derating (Ta 85C) I / C 0.5 mA/C F Peak transient forward current (Note 1) I 1 A FPT Reverse voltage V 5 V R Input power dissipation PD 40 mW Input power dissipation derating (Ta 85C) PD/C -1.0 mW/C Output current I 10 mA O Output current derating (Ta 85C) IO/C -0.25 mA/C Output voltage V 6 V O Supply voltage V 6 V CC Output power dissipation P 40 mW O Operating temperature range Topr 40 to 100 C Storage temperature range Tstg 55 to 125 C Lead solder temperature(10 s) Tsol 260 C Isolation voltage (AC,60 s, R.H. 60 %) (Note 2) BVs 3750 Vrms Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (Handling Precautions/Derating Concept and Methods) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note 1 : Pulse width PW 1 s, 300 pps. Note 2 :This device is regarded as a two terminal device : pins 1 and 3 are shorted together, as are pins 4,5 and 6. Recommended Operating Conditions Characteristic Symbol Min Typ. Max Unit Input current ON I 8 18 mA F(ON) Input voltage , OFF V 0 0.8 V F(OFF) Supply voltage V 4.5 5.0 5.5 V CC Operating temperature Topr -40 100 C Note: Recommended operating conditions are given as a design guideline to obtain expected performance of the device. Additionally, each item is an independent guideline respectively. In developing designs using this product, please confirm specified characteristics shown in this document. Note: The detector of this product requires a power supply voltage (V ) of 4.5 V or higher for stable operation. CC If the V is lower than this value, an I may increase, or an output may be unstable. CC CC Be sure to use the product after checking the supply current, and the operation of a power-on/-off. Correlation between Input current, switching speed and drive circuit (reference information). Input current Test Circuit Typical switching speed (IF) 1 12mA 21 to 23 MBd (Page 4) 1 8mA 18 to 20 MBd (Page 4) 2 8mA 23 to 27 MBd (Page 4, With Speed up capacitor) 2019 2 2019-10-10 Toshiba Electronic Devices & Storage Corporation LED DETECTOR