TLP2391 Toshiba

TLP2391 Photocouplers GaAAs Infrared LED & Photo IC TLP2391TLP2391TLP2391TLP2391 1. 1. ApplicationsApplications 1. 1. ApplicationsApplications Programmable Logic Controllers (PLCs) Industrial Inverters High-Speed Digital Interfacing for Instrumentation and Control Devices 2. 2. 2. 2. GeneralGeneralGeneralGeneral The Toshiba TLP2391 consists of two high-output GaAAs light-emitting diode coupled with a high-gain, high- speed photo detector. It is housed in the SO6 package. Since it is making two LED reverse parallel, it can be dealt with both sinking and sourcing input signals. Since TLP2391 has guaranteed 1 mA low supply current (I /I ), and 2.5 mA (V = 5 V) low threshold input CCL CCH CC current(I ), it contributes to energy saving of devices. FHL The detector has a totem-pole output stage with current sourcing and sinking capabilities. The TLP2391 has an internal Faraday shield that provides a guaranteed common-mode transient immunity of 20 kV/s. 3. 3. FeaturesFeatures 3. 3. FeaturesFeatures (1) Inverter logic type (Totem pole output) (2) Package: SO6 (3) Operating temperature: -40 to 125 (4) Supply voltage: 2.7 to 5.5 V (5) Threshold input current: 2.3 mA (max) (V = 3.3 V) CC : 2.5 mA (max) (V = 5 V) CC (6) Supply current: 1 mA (max) (7) Data transfer rate: 10 MBd (typ.) (NRZ) (8) Propagation delay time: 100 ns (max) (9) Pulse width distortion: 30 ns (max) (10) Isolation voltage: 3750 Vrms (min) (11) Safety standards UL-approved: UL1577, File No.E67349 cUL-approved: CSA Component Acceptance Service No.5A File No.E67349 (Note 1) VDE-approved: EN60747-5-5 (Note 1)(Note 1)(Note 1) CQC-approved: GB4943.1, GB8898 Thailand Factory Note 1: When an EN60747-5-5 approved type is needed, please designate the Option (V4)Option (V4)Option (V4)Option (V4). Start of commercial production 2013-11 2015 Toshiba Corporation 2015-12-15 1 Rev.3.0TLP2391 4. 4. 4. 4. Packaging and Pin ConfigurationPackaging and Pin ConfigurationPackaging and Pin ConfigurationPackaging and Pin Configuration 1: Anode / Cathode 3: Cathode / Anode 4: GND 5: V (Output) O 6: V CC 11-4L1S 5. 5. 5. 5. Internal Circuit (Note)Internal Circuit (Note)Internal Circuit (Note)Internal Circuit (Note) Note: A 0.1-F bypass capacitor must be connected between pin 6 and pin 4. 6. 6. 6. 6. Principle of OperationPrinciple of OperationPrinciple of OperationPrinciple of Operation 6.1. 6.1. 6.1. 6.1. Truth TableTruth TableTruth TableTruth Table Input LED Output H ON L L OFF H 6.2. 6.2. 6.2. 6.2. Mechanical ParametersMechanical ParametersMechanical ParametersMechanical Parameters Characteristics Min Unit Creepage distances 5.0 mm Clearance distances 5.0 Internal isolation thickness 0.4 2015 Toshiba Corporation 2015-12-15 2 Rev.3.0