NPN Silicon Photodarlington OP300SL Series Features: Narrow receiving angle Variety of sensitivity ranges Enhanced temperature range PCBoard mounting Mechanically and spectrally matched to OP123 and OP223 LEDs Description: Each device in this series is a NPN silicon photodarlington in a hermetically sealed pill package with a narrow receiving angle that provides excellent on-axis coupling. Photodarlingtons are normally used in applications with low light signal levels, where more current gain is needed than phototransistors can provide. Components in the OP300 series are mechanically and spectrally matched to the OP123 and OP223 series. Please refer to Application Bulletins 208 and 210 for additional design information and reliability (degradation) data, and to Application Bulletin 202 for pill-type soldering to PCBoard. Applications: Ordering Information Light Current Non-contact reflective object sensor Machine safety Input Power Part I (mA) Viewing C(ON) 2 Assembly line automation End of travel sensor E (mW/cm ) E Number Sensor Min / Max Angle Machine automation Door sensor OP300SL 0.8 / NA 1.0 with OP301SL 0.8 / 2.4 2870K OP302SL 1.8 / 5.4 Darlington or 35 OP303SL 3.6 / 12.0 0.4 with OP304SL 7.0 / 21.0 890nm 1 OP305SL 14.0 / NA 2 Pin Sensor 1 Collector 2 Emitter MILLIMETERS DIMENSIONS ARE IN: INCHES OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. RoHS OPTEK Technology Inc. 1645 Wallace Drive, Carrollton, Texas 75006 Issue A 05/07 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors optekinc.com www.optekinc.com Page 1 of 4 NPN Silicon Photodarlington OP300SL Series Absolute Maximum Ratings (T =25C unless otherwise noted) A Collector-Emitter Voltage 15.0 V Emitter-Collector Voltage 5.0 V Storage Temperature Range -65 C to +150 C Operating Temperature Range -65 C to +125 C (1)(2) Soldering Temperature (5 seconds with soldering iron) 260 C (3) Power Dissipation 50 mW Continuous Collector Current 50 mA Electrical Characteristics (T = 25 C unless otherwise noted) A SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS On-State Collector Current 0.8 - - OP300SL 0.8 - 2.4 OP301SL 1.8 - 5.4 (4) 2(5) I OP302SL mA V = 5.0 V, E = 1.0 or 0.4 mW/cm C(ON) CE E 3.6 - 12.0 OP303SL 7.0 - 21.0 OP304SL 14.0 - - OP305SL I Collector-Dark Current - - 1.0 A V = 10 V, E = 0 CEO CE E V Collector-Emitter Breakdown Voltage 15.0 - - V I = 100 A (BR)CEO C V Emitter-Collector Breakdown Voltage 5.0 - - V I = 100 A (BR)ECO E Collector-Emitter Saturation Voltage (4) 2(5) V OP300SL, OP301SL - - 1.1 I = 0.4 mA, E = 1.0 or 0.4 mW/cm CE(SAT) C E V 2(5) OP302SL through OP305SL - - 1.1 I = 1.0 mA, E = 1.0 or 0.4 mW/cm C E Notes: (1) Refer to Application Bulleting 202, which discusses proper techniques for soldering pill-type devices to PCBoards. (2) No clean or low solids. RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering. (3) Derate linearly 0.5 mW/ C above 25 C. (4) Junction temperature maintained at 25 C. 2 2 (5) Light source is an unfiltered tungsten bulb operating at CT = 2870 K at E =1.0 mW/cm or 890nm at E =0.4 mW/cm . E E OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A 05/07 OPTEK Technology Inc. 1645 Wallace Drive, Carrollton, Texas 75006 Page 2 of 4 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors optekinc.com www.optekinc.com