OPI1264A TT Electronics

Optically Coupled Isolator OPI110, OPI1264 Series Features: 15 kV electrical isolation Choice of phototransistor Low-cost plastic housing UL recognized File No. E58730 Description: Each Optoisolator in this data sheet contains an infrared Light Emitting Diode (LED) and a NPN silicon Photosensor. The OPI110 and OPI1264 devices have 890 nm Light Emitting Diode (LED) and NPN phototransistor sensor. The devices are sealed in a precast opaque housing with a optically transmissive path between the LED and the photosensor. The Optoisolators in this data sheet are UL recognised under E58730. This series is designed for transmission of information between one power supply voltage and another where the potentials during surge conditions are not greater than the guaranteed isolation voltage. Custom electrical, wire and cabling and connectors are available. Contact your local representative or OPTEK for more information. Applications: High voltage isolation between input and output Electrical isolation in dirty environments Industrial equipment Medical equipment Ordering Information LED Isolation CTR V Lead CE Part I (mA) F Peak Sensor Voltage Min / (Volts) Length / Number Typ / Max Wavelength (,000) Max Max Spacing OPI110 12.5 / NA OPI110A 25 / NA Transistor 10 / 40 OPI110B 50 / 125 OPI110C 100 / NA 890 nm 15 30 0 . 5 0 / 0.55 OPI1264 12.5 / NA OPI1264A 25 / NA Transistor 10 / 40 OPI1264B 50 / 125 OPI1264C 100 / NA General Note TT Electronics OPTEK Technology TT Electronics reserves the right to make changes in product specificaoti n without 1645 Wallace Drive, Carrollton, TX 75006 Ph: +1 972 323 2200 nocti e or liability. All informaoti n is subject to TT Electronics own data and is www.ttelectronics.com sensors ttelectronics.com considered accurate at time of going to print. Issue C 11/2017 Page 1 TT electronics plc Optically Coupled Isolator OPI110, OPI1264 Series o Absolute Maximum Ranti gs (T = 25 C unless otherwise noted) A Storage Temperature -40 C to +100 C Operating Temperature -40 C to +85 C (1)(2) Input-to-Output Isolation Voltage 15 kVDC (3) Lead Soldering Temperature (1/16 (1.6 mm) from case for 5 seconds with soldering iron) 260 C Input Diode Forward DC Current 40 mA Reverse DC Voltage 2 V (4) Power Dissipation 50 mW Output Photosensor Collector-Emitter Voltage 30 OPI110, OPI1264 Emitter -Collector Voltage 5 (5) Power Dissipation 100 mW Notes: (1) Measured with input and output leads shorted. Typical input/output capacitance is 0.06 pF. (2) UL recognioti n is for 15kV dc for one minute. (3) RMA flux is recommended. The duration can be extended to 10 seconds maximum when ofl w soldering. (4) Derate linearly 0.83 mW/C above 25C. (5) Derate linearly 1.67 mW/C above 25C. OPI110 OPI1264 1 4 1 4 3 3 2 2 General Note TT Electronics OPTEK Technology TT Electronics reserves the right to make changes in product specificaoti n without 1645 Wallace Drive, Carrollton, TX 75006 Ph: +1 972 323 2200 nocti e or liability. All informaoti n is subject to TT Electronics own data and is www.ttelectronics.com sensors ttelectronics.com considered accurate at time of going to print. Issue C 11/2017 Page 2 TT electronics plc