Vertical Cavity Surface Emitting Laser in Lateral Package OPV382 Features: 850 nm VCSEL technology High thermal stability Low drive current High output power Narrow beam angle Description: The OPV382 is a Vertical Cavity Surface Emitting Laser (VCSEL) packaged in a dome lens lateral package. VCSELs offer many advantages in sensing applications when compared to infrared LEDs. These devices require substantially lower drive currents to obtain the same amount of output power as LEDs. This feature allows VCSELs to be used in low power consumption applications such as battery operated equipment. The dome lens packaging creates a narrow beam angle from the device. Long distance applications may benefit from this feature as secondary optics may be eliminated, reducing total system cost. The OPV382 is optically and spectrally compatible with Opteks standard detector products such as the OP500 series phototransistors, OP530 series photodarlingtons and the OP900 series photodiodes. Applications: Emission Surface Non-contact position sensing Photoelectric sensors Optical encoders Light curtains OPV382 Pin Connection VCSEL 1 Cathode 2 Anode 1 2 Additional laser safety information can be found on the Optek website. See application bulletin 221. Classification is not marked on the device due to space limitations. See package out- Pb line for centerline of optical radiance. Oper- ating devices beyond maximum rating may result in hazardous radiation exposure. LEAD FREE General Note TT Electronics Optek Technology, Inc. TT Electronics reserves the right to make changes in product specificaoti n without 1645 Wallace Drive, Ste. 130, Carrollton, TX USA 75006 Ph: +1 972 323 2200 nocti e or liability. All informaoti n is subject to TT Electronics own data and is www.ttelectronics.com sensors ttelectronics.com considered accurate at time of going to print. Issue B 07/2018 Page 1 TT electronics plc Vertical Cavity Surface Emitting Laser in Lateral Package OPV382 Electrical Specifications Absolute Maximum Ratings (T = 25 C unless otherwise noted) A Storage Temperature Range -40 to +100 C Operating Temperature Range 0 to +85 C (1) Lead Soldering Temperature 1/16 inch (1.6mm) from case for 5 sec with soldering iron 260 C Maximum Forward Peak Current, Continuous 12 mA Maximum Reverse Voltage 5 V Maximum Forward Current, pulsed (1s P.W., 10% D.C.) 48 mA Electrical Characteriscti s (T = 25 C unless otherwise noted) A SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS P Total Power Out 1.5 mW I = 7 mA OT F I Threshold Current 3.0 mA Note 2 TH V Forward Voltage 2.2 V I = 7 mA F F I Reverse Current 100 nA V = 5 V R R R Series Resistance 20 55 ohms Note 3 S Slope Efficiency 0.28 mW/mA Note 4 Wavelength 840 860 nm Optical Bandwidth 0.85 nm Beam Divergence 6 Degrees FWHM T Temp Coefficient of Slope Efficiency -0.50 %/C (0 - 70C), Note 4 /T Temp Coefficient of Wavelength 0.06 nm/C (0 - 70C) Temp Variance of Threshold Current 1.0 mA l (0 - 70C), Note 2 TH Temp Coefficient for Forward Voltage -2.5 V /T mV/C (0 - 70C) F NOTES: (1) RMA flux is recommended. Solder dwell time can be increased to 10 seconds when flow soldering. (2) Threshold Current is based on the two line intersection method specified in Telcordia GR-468-Core. Line 1 from 4 mA to 6 mA. Line 2 from 0 mA to 0.5 mA. (3) Series Resistance is the slope of the Voltage-Current line from 5 to 8 mA. (4) Slope efficiency, is the slope of the best fit LI line from 5 mA to 8 mA with 0.25mA test intervals. General Note TT Electronics Optek Technology, Inc. TT Electronics reserves the right to make changes in product specificaoti n without 1645 Wallace Drive, Ste. 130, Carrollton, TX USA 75006 Ph: +1 972 323 2200 nocti e or liability. All informaoti n is subject to TT Electronics own data and is www.ttelectronics.com sensors ttelectronics.com considered accurate at time of going to print. Issue B 07/2018 Page 2 TT electronics plc