8 7 6 5 4 3 2 1 VICOR CONFIDENTIAL REVISIONS THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR HEREWITH IS NOT TO BE REPRODUCED, USED OR DISCLOSED IN WHOLE OR IN PART TO ANYONE WITHOUT REV DESCRIPTION DATE APPROVED THE PERMISSION OF VICOR CORP. 1 RELEASED PER E053437 LEK 11/15/05 EF F F 2 REVISED PER E090943 AR 06/05/09 REJH 3 REDRAWN PER E100903 DCS 7/14/10 KUK 2.28 .49 1.300 .650 .545 E E .69 1.270 2.650 D D .143/.149 ( 27) THRU .250 C BORE X .070 DP (6) PL. C C NOTES: 1. MATERIAL: EXTRUSION, SEE SHEET 2 OF 2 2. REMOVE ALL LOOSE AND HANGING BURRS, OTHERWISE, BURRS SHALL NOT EXCEED .003. 3. CLEAR FINISH, RoHS COMPLIANT CHROMIUM FREE PER CST-0001 LATEST REVISION. B B 4. DENOTES CRITICAL CHARACTERISTIC FOR LOT INSPECTION. 5. DIMENSIONS ARE INCHES ONLY. SWD DRAWN DATE VICOR L. KNIGHT 5/23/05 UNLESS OTHERWISE SPECIFIED MATERIAL HEATSINK, MICRO, LOW PROFILE DIMENSIONS ARE INCH MM TOLERANCES ARE: SEE NOTES DECIMALS ANGLES (2.28L X 2.65 W) A A X.XX X.X = 0.01 0.25 1 X.XXX X.XX = 0.005 0.127 SIZE CAGE CODE DWG NO REV FINISH THIRD ANGLE PROJECTION SEE NOTES C 67131 30095 3 SCALE 2 : 1 SHEET 1 OF 2 DO NOT SCALE DRAWING 8 7 6 5 4 3 2 18 7 6 5 4 3 2 1 VICOR CONFIDENTIAL REVISIONS THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR HEREWITH IS NOT TO BE REPRODUCED, USED OR DISCLOSED IN WHOLE OR IN PART TO ANYONE WITHOUT REV DESCRIPTION DATE APPROVED THE PERMISSION OF VICOR CORP. SEE SHEET 1 OF 2 F F 2.650 .895 * .860 ( .600 ) .493 SEE NOTE 4 E E .416 .318 .150 R.020 (5) PL255 .130 R R.030 78.014 .159 (6) PL. BOTH ENDS .061 .121 .053 .040 * .259 D D .545 3 * 20 .125 R.020 R.030 * .072 .061 SEE DETAIL A (4) PL. (3) PL. BOTH ENDS .257 1.480 .565 .514 DETAIL A C C SCALE 4 : 1 .575 1.499 B B NOTES: 1. MATERIAL: ALUMINUM 6063-T5. 2. * DENOTES DIMENSION TO THEORETICAL SHARP CORNER. 3. DIMENSIONS SHOWN CAN BE USED ON OPPOSITE ENDS AS NEEDED. 4. (4) EQUAL SPACES .150=.600 (TOL. TO BE NON-CUMULATIVE) 5. UNLESS OTHERWISE SPECIFIED: A. DRAFT ANGLES TO BE 1.5. SWD DRAWN DATE B. RADII TO BE 0.020. VICOR 6. DIMENSIONS ARE INCHES ONLY. A. RAGIPANI 06/05/09 UNLESS OTHERWISE SPECIFIED MATERIAL HEATSINK, MICRO, LOW PROFILE DIMENSIONS ARE INCH MM TOLERANCES ARE: SEE NOTES DECIMALS ANGLES (2.28L X 2.65W), EXTRUSION A A X.XX X.X = 0.01 0.25 1 X.XXX X.XX = 0.005 0.127 SIZE CAGE CODE DWG NO REV FINISH THIRD ANGLE PROJECTION SEE NOTES C 67131 30095 3 SCALE 2 : 1 SHEET 2 OF 2 DO NOT SCALE DRAWING 8 7 6 5 4 3 2 1