8 7 6 5 4 3 2 1 VICOR CONFIDENTIAL REV. DESCRIPTION DATE APPROVED THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR HEREWITH IS NOT TO BE REPRODUCED, USED OR DISCLOSED IN WHOLE OR IN PART TO ANYONE WITHOUT THE PERMISSION OF VICOR CORP. 1 RELEASED PER E053437 LEK 11/15/05 EF 2 REVISED PER E091977a GCK 11/2/09 MM F F 3 REDRAWN PER E100902 DCS 7/14/10 KUK FULL R 4 REVISED PER E120702 ZMB 07/31/12 REJH (6) PL. SEE NOTE 6 .49 .650 E <> E 1.300 2.28 <> <> .16 (12) PL. SEE NOTE 5 D D <> .910 1.270 30 DRILL THRU .10 <> ( .1285 ) (6) PL. 1.470 C C .90 -A- <> .005 .190 .100 .010 MATL TO BE REMOVED B B NOTES: DRAWN BY DATE SWD VICOR 1. MATERIAL: EXTRUSION SEE SHEET 2 OF 2. P.E.IENI 06/29/05 2. REMOVE ALL BURRS AND SHARP EDGES. UNLESS OTHERWISE SPECIFIED <> 3. CLEAR FINISH, RoHS COMPLIANT PER CST-0001, LATEST DIMENSIONS ARE : INCH / MM HS CFG LONG, .9H, LOW REVISION PER A.) CHROMIUM FREE, OR B.) TRIVALENT CHROMIUM TOLERANCES ARE: IN ACCORDANCE WITH MIL-DTL-5541, TYPE II, CLASS 1A OR 3. DECIMALS ANGLES A A FLOW, THRU HOLE X.XX X.X = 0.01 0.25 1 SEE CST-0003 FOR TYPES OF AVAILABLE FINISHES. X.XXX X.XX = 0.005 0.127 4.< DENOTES CRITICAL CHARACTERISTIC FOR LOT INSPECTION. SIZE CAGE CODE DWG NO REV THIRD ANGLE PROJECTION 5. DIMENSIONS APPLIES AT SURFACE -A- (12) PL. C 67131 30183 4 6. MACHINED SURFACE TO BE .010 MAX BELOW SURFACE -A- (6) PL. 7. DIMENSIONS ARE INCHES ONLY. 2:1 2 SCALE SHEET OF 1 DO NOT SCALE DRAWING 8 7 6 5 4 3 2 1A 8 7 6 5 4 3 2 1 VICOR CONFIDENTIAL REVISIONS THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR HEREWITH IS NOT TO BE REPRODUCED, USED OR DISCLOSED IN WHOLE OR IN PART TO ANYONE WITHOUT REV DESCRIPTION DATE APPROVED THE PERMISSION OF VICOR CORP. SEE SHEET 1 F F 3 1.5 EACH SIDE OF VERT SEE DETAIL A 1.756 E E .023 R.018 (2) PL036 .031 .040 .910 .080 R.035 (14) PL. D D R.030 (33) PL215 .200 .110 * .084 * .180 R.010 (2) PL. (3) PL. (2) PL752 R.035 (12) PL. * .185 * .087 C C (2) PL. (2) PL. +.020 .007 1.470 -.000 (2) PL191 DETAIL A SCALE 8 : 1 C L B B PROFILE COMMON FOR 30183 30190 * .087 NOTES: 1. MATL: ALUMINUM 6063-T5 SWD 2. * DENOTES DIMENSION TO THEORETICAL SHARP CORNER. DRAWN BY DATE VICOR 3. ALL DIMENSIONS ARE CRITICAL CHARACTERISTICS. G.C. KEAY 11/2/09 4. RoHS COMPLIANT PER CST-0001 LATEST REVISION. UNLESS OTHERWISE SPECIFIED 5. WORKMANSHIP STANDARDS WS-0004, WS-0006 AND WS-0007 APPLY TO THIS PART. DIMENSIONS ARE : INCH / MM HS CFG LONG, .9H, LOW 6. DIMENSIONS ARE INCHES ONLY. TOLERANCES ARE: DECIMALS ANGLES A A FLOW THRU HOLE EXTRUSION X.XX X.X = 0.01 0.25 1 X.XXX X.XX = 0.005 0.127 SIZE CAGE CODE DWG NO REV THIRD ANGLE PROJECTION C 67131 30183 4 SCALE 2:1 2 2 SHEET OF DO NOT SCALE DRAWING 8 7 6 5 4 3 2 1
