30720 Vicor

8 7 6 5 4 3 2 1 VICOR CONFIDENTIAL REVISIONS THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR HEREWITH IS NOT TO BE REPRODUCED, USED OR DISCLOSED IN WHOLE OR IN PART TO ANYONE WITHOUT REV DESCRIPTION DATE APPROVED THE PERMISSION OF VICOR CORP. 1 RELEASED PER E053437 LEK 11/15/05 EF F F 2 REVISED PER E090943 AR 06/03/09 REJH 3 REDRAWN PER E100871 DCS 6/8/10 KUK 30 DRILL THRU .120 SEE NOTE 6 ( .1285 ) (2) PL. (6) PL.300 (2) PL. E E R.110 MAX (8) PL. 2.22 2.000 .130 .11 TYP .410 D D SEE NOTE 5 1.800 .50 3.600 4.600 C C .40 .190 .100 -A- .005 .010 MATL TO BE REMOVED B B NOTES: 1. MATERIAL: EXTRUSION SEE SHEET 2 OF 2 2. REMOVE ALL BURRS AND SHARP EDGES. 3. CLEAR FINISH, RoHS COMPLIANT, CHROMIUM FREE PER CST-0001 LATEST REVISION. 4. DENOTES CRITICAL CHARACTERISTIC FOR LOT INSPECTION. 5. DIMENSIONS APPLIES AT SURFACE -A- (2) PL. SWD DRAWN DATE 6. MACHINED SURFACE TO BE .010 MAX BELOW SURFACE -A- (6) PLACES. VICOR 7. DIMENSIONS ARE INCHES ONLY D.P. KELLY 10/05 UNLESS OTHERWISE SPECIFIED MATERIAL HS CFG .4H X-FLOW DIMENSIONS ARE INCH MM TOLERANCES ARE: SEE NOTES DECIMALS ANGLES LOW FLOW THRU HOLE A A X.XX X.X = 0.01 0.25 1 X.XXX X.XX = 0.005 0.127 SIZE CAGE CODE DWG NO REV FINISH THIRD ANGLE PROJECTION SEE NOTES C 67131 30720 3 SCALE 1 : 1 SHEET 1 OF 1 DO NOT SCALE DRAWING 8 7 6 5 4 3 2 18 7 6 5 4 3 2 1 VICOR CONFIDENTIAL REVISIONS THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR HEREWITH IS NOT TO BE REPRODUCED, USED OR DISCLOSED IN WHOLE OR IN PART TO ANYONE WITHOUT REV DESCRIPTION DATE APPROVED THE PERMISSION OF VICOR CORP. SEE SHEET 1 OF 2 F F C L E E .012 (2) PL. R.035 R.035 (2) PL. SEE DETAIL A (48) PL. A .410 D D .235 .200 .110 1.756 * .138 * .060 * .058 * .056 (5) PL. (14) PL. (8) PL. (2) PL. R.010 * .133 3 * .296 (4) PL. (18) PL. 1.5 EACH +.020 4.600 SIDE OF VERT -.000 R.018 (2) PL. C C .023 .040 .031 .036 .080 .252 R.030 (8) PL. C L PROFILE COMMON * .060 FOR * .030 30778 B B 30720 DETAIL A SCALE 4 : 1 NOTES: 1. MAT L: ALUMINUM 6063-T5 SWD DRAWN DATE 2. *DENOTES DIMENSION TO THEORETICAL SHARP CORNER VICOR 3. DIMENSIONS ARE INCHES ONLY A. RAGIPANI 06/03/09 UNLESS OTHERWISE SPECIFIED MATERIAL HS CFG .4H X-FLOW, LOW DIMENSIONS ARE INCH MM TOLERANCES ARE: XXXXX DECIMALS ANGLES FLOW THRU HOLE, EXTRUSION A A X.XX X.X = 0.01 0.25 1 X.XXX X.XX = 0.005 0.127 SIZE CAGE CODE DWG NO REV FINISH THIRD ANGLE PROJECTION XXXXX C 67131 30720 3 SCALE 2 : 1 SHEET 2 OF 2 DO NOT SCALE DRAWING 8 7 6 5 4 3 2 1