LH1526AACTR Vishay

333 3 LH1526AB, LH1526AAC, LH1526AACTR www.vishay.com Vishay Semiconductors Dual 1 Form A Solid-State Relay FEATURES Dual channel Extremely low operating current 1 8 S1 High speed operation Isolation test voltage 5300 V RMS 2 7 S1 Current limit protection 3 6 S2 Load voltage 400 V Load current 125 mA 4 5 S2 Clean bounce free switching Low power consumption Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 APPLICATIONS LINKS TO ADDITIONAL RESOURCES General telecom switching Battery powered switch applications Related 3D Models Models Footprints Schematics Instrumentation Documents Industrial controls DESCRIPTION The LH1526 dual 1 Form A relays are SPST normally open AGENCY APPROVALS switches that can replace electromechanical relays in many UL applications. The relays require a minimal amount of LED cUL drive current to operate, making it ideal for battery powered VDE and power consumption sensitive applications. The relay is constructed using a GaAIAs LED for actuation control and CQC MOSFET switches for the output. In addition, the relay employs current-limiting circuitry to provide overvoltage protection. ORDERING INFORMATION DIP SMD L H 1526 A T R PART NUMBER ELECTR. PACKAGE TAPE AND 7.62 mm > 0.1 mm VARIATION CONFIG. REEL PACKAGE UL SMD-8, tube LH1526AAC SMD-8, tape and reel LH1526AACTR DIP-8, tube LH1526AB Rev. 2.2, 02-Jul-2020 Document Number: 83825 1 For technical questions, contact: optocoupleranswers vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 DDD DLH1526AB, LH1526AAC, LH1526AACTR www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS (T = 25 C, unless otherwise specified) amb PARAMETER CONDITIONS SYMBOL VALUE UNIT INPUT IRED continuous forward current I 50 mA F IRED reverse voltage V 5V R Input power dissipation P 80 mW diss OUTPUT DC or peak AC load voltage V 400 V L Continuous DC load current at 25 C, I 125 mA L one channel Continuous DC load current at 25 C, I 100 mA L two channels SSR output power dissipation P 550 mW diss SSR Ambient temperature range T -40 to +85 C amb Storage temperature range T -40 to +150 C stg Soldering temperature t = 10 s max. T 260 C sld Note Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability ELECTRICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT INPUT IRED forward current, switch turn-on I = 100 mA, t = 10 ms I -- 0.9 mA L Fon IRED forward current, switch turn-off V = 350 V I 0.001 0.150 - mA L Foff IRED forward voltage I = 1.5 mA V 0.80 1.28 1.40 V F F IRED reverse current V = 5 V I - - 10 A R R OUTPUT On-resistance I = 1.5 mA, I = 50 mA R -22 36 F L ON Off-resistance I = 0 mA, V = 100 V R - 5000 - G F L OFF I = 0 mA, V = 100 V I - < 1 200 nA F L O Off-state leakage current I = 0 mA, V = 350 V I - 6 1000 nA F L O I = 0 mA, V = 1 V, f = 1 MHz C -39 - pF F L O Output capacitance I = 0 mA, V = 50 V, f = 1 MHz C -6 - pF F L O Current limit AC/DC I = 1.5 mA, t = 5 ms, V = 6 V I 170 350 450 mA F L limit TRANSFER Capacitance (input to output) V = 1 V, f = 1 MHz C -0.7 - pF IO IO Note Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluations. Typical values are for information only and are not part of the testing requirements SWITCHING CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT I = 1.5 mA, I = 50 mA, R = 1 k t -0.6 - ms F L L on Turn-on time I = 5 mA, I = 50 mA, R = 1 k t -0.15 1 ms F L L on I = 1.5 mA, I = 50 mA, R = 1 k t -0.04- ms F L L off Turn-off time I = 5 mA, I = 50 mA, R = 1 k t - 0.05 1.5 ms F L L off Rev. 2.2, 02-Jul-2020 Document Number: 83825 2 For technical questions, contact: optocoupleranswers vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000