LH1532FP, LH1532FPTR www.vishay.com Vishay Semiconductors Dual 1 Form A Solid-State Relay FEATURES 8 1 S1 Solid-state relay (equivalent to AQW210S) - Typical R 20 ON 2 7 S1 - Load voltage 350 V 6 3 S2 - Load current 120 mA - Current limit protection 5 4 - High surge capability S2 i179050-1 - Clean bounce free switching - Low power consumption - High reliability monolithic receptor DESCRIPTION Two independent relays in a single package The LH1532FP is a dual 1 form A (SPST) which can replace Package - flat pak electromechanical relays in many applications. They are Isolation test voltage, 3000 V RMS constructed using a GaAlAs LED for activation control and an integrated monolithic die for the switch output. The die is Material categorization: For definitions of compliance comprised of a photodiode array, switch control circuity and please see www.vishay.com/doc 99912 MOSFET switches. The SSR features low on-resistance, APPLICATIONS high breakdown voltage and current-limit circuitry that protects the relay from telephone line induced lightning General telecom switching surges. - On/off hook control - Ring relay AGENCY APPROVALS - Ground start UL1577, file no. E52744 system code O Industrial controls DIN EN 60747-5-5 (VDE 0884) - Triac predriver FIMKO approval - Output modules CQC GB4943.1-2011 (suitable for installation altitude below 2000 m) Peripherals - Transducer driver Instrumentation - Automatic tuning/balancing - Flying capacitor - Analog multiplexing Note See solid-state relays (application note 56) ORDERING INFORMATION SMD- L H 1 532 F P T R 7 mm PART NUMBER PACKAGE TAPE AND CONFIG. REEL PACKAGE UL, FIMKO SOP-8, tubes LH1532FP SOP-8, tape and reel LH1532FPTR Rev. 1.7, 12-Apr-13 Document Number: 83830 1 For technical questions, contact: optocoupleranswers vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000LH1532FP, LH1532FPTR www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL VALUE UNIT INPUT LED continuous forward current I 50 mA F LED reverse voltage I 10 A V 6V R R OUTPUT DC or peak AC load voltage I 50 A V 350 V L L Continuous DC load current I 120 mA L SSR Ambient temperature range T - 40 to + 85 C amb Storage temperature range T - 40 to + 125 C stg (1) Soldering temperature t = 10 s max. T 260 C sld Isolation test voltage t = 1 s V 3000 V ISO RMS 12 V = 500 V, T = 25 C R 10 IO amb IO Isolation resistance 11 V = 500 V, T = 100 C R 10 IO amb IO Total power dissipation P 600 mW tot Notes Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability. (1) Refer to reflow profile for soldering conditions for surface mounted devices. ELECTRICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT INPUT LED forward current, switch turn-on I = 100 mA, t = 10 ms I 1.2 3 mA L Fon LED forward current, switch turn-off V = 300 V I 0.2 mA L Foff LED forward voltage I = 10 mA V 1 1.22 1.5 V F F OUTPUT On-resistance I = 5 mA, I = 50 mA R 20 25 F L ON Off-resistance I = 0 mA, V = 100 V R 5000 G F L OFF Current limit I = 5 mA, t = 5 ms I 170 210 250 mA F Limit I = 0 mA, V = 100 V I 0.6 200 nA F L O Output off-state leakage current I = 0 mA, V = 350 V I 1A F L O Output capacitance I = 0 mA, V = 1 V C 55 pF F L O Pole-to-pole capacitance (S1 to S2) I = 5 mA 0.5 pF F TRANSFER Switch offset I = 5 mA V 0.15 V F OS Note Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluations. Typical values are for information only and are not part of the testing requirements. SWITCHING CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT Turn-on time I = 5 mA, I = 50 mA t 1.1 2.5 ms F L on Turn-off time I = 5 mA, I = 50 mA t 0.06 2.5 ms F L off Rev. 1.7, 12-Apr-13 Document Number: 83830 2 For technical questions, contact: optocoupleranswers vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000