OLED-128O064D-BPP3N00000 www.vishay.com Vishay 128 x 64 Graphic OLED FEATURES Type: graphic Display format: 128 x 64 dots Built-in controller: SSD1306BZ Duty cycle: 1/64 +3 V power supply 2 Interface: 6800, 8080, serial, and I C Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 MECHANICAL DATA ABSOLUTE MAXIMUM RATINGS ITEM STANDARD VALUE UNIT STANDARD VALUE ITEM SYMBOL UNIT Module dimension 26.7 x 19.26 x 1.65 MIN. MAX. Viewing area 23.938 x 12.058 Supply voltage V 04 DD (1)(2) Active area 21.738 x 10.858 for logic mm V Dot size 0.148 x 0.148 Supply voltage V 015 CC (1)(2) for display Dot pitch 0.17 x 0.17 Mounting hole n/a Operating temperature T -40 +80 OP C Storage temperature T -40 +80 STG Notes (1) All the above voltages are on the basis of V = 0 V. SS (2) When this module is used beyond the above absolute maximum ratings, permanent breakage of the module may occur. Also, for normal operations, it is desirable to use this module under the conditions according to section 6 Electrical Characteristics. If this module is used beyond these conditions, malfunctioning of the module can occur and the reliability of the module may deteriorate. ELECTRICAL CHARACTERISTICS STANDARD VALUE ITEM SYMBOL CONDITION UNIT MIN. TYP. MAX. Supply voltage for logic V - 2.8 3.0 3.3 DD Supply voltage for display V - 101215 CC Input high voltage V - 0.8 V -V IH DD DDI/O V Input low voltage V - 0 - 0.2 V IL DD Output high voltage V - 0.9 V -V OH DD DDI/O Output low voltage V - 0 - 0.1 V OL DD 50 % check board operating current I V = 12 V 9 10 12 mA CC CC OPTIONS EMITTING COLOR YELLOW GREEN RED BLUE WHITE --- Yes - Revision: 14-Dec-16 Document Number: 37902 1 For technical questions, contact: displays vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 OLED-128O064D-BPP3N00000 www.vishay.com Vishay INTERFACE PIN FUNCTION PIN NO. SYMBOL FUNCTION Reserved pin (supporting pin) 1 NC (GND) The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground. 2C2N Positive terminal of the flying inverting capacitor negative terminal of the flying boost capacitor 3C2P The charge-pump capacitors are required between the terminals. They must be floated when the converter is not 4C1P used. 5C1N Power supply for DC/DC converter circuit 6V This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external BAT source when the converter is used. It should be connected to V when the converter is not used. DD 7NC NC Ground of logic circuit 8V SS This is a ground pin. It also acts as a reference for the logic pins. It must be connected to external ground. Power supply for logic circuit. 9V DD This is a voltage supply pin. It must be connected to external source. Communicating protocol select 10 BS0 These pins are MCU interface selection input. See the following table: 2 I C 3-wire SPI 4-wire SPI 8-bit 68XX parallel 8-bit 80XX parallel 11 BS1 BS0 010 0 0 BS1 100 0 1 12 BS2 BS2 000 1 1 Chip select 13 CS This pin is the chip select input. The chip is enabled for MCU communication only when CS is pulled low. Power reset for controller and driver 14 RES This pin is reset signal input. When the pin is low, initialization of the chip is executed. Data / command control This pin is data / command control pin. When the pin is pulled high, the input at D7 to D0 is treated as display data. When the pin is pulled low, the input at D7 to D0 will be transferred to the command register. For detail relationship 15 D/C to MCU interface signals, please refer to the timing characteristics diagrams. When the pin is pulled high and serial interface mode is selected, the data at SDIN is treated as data. When it is pulled low, the data at SDIN will be 2 transferred to the command register. In I C mode, this pin acts as SA0 for slave address selection. Read / write select or write This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as read / write (R/W ) selection input. Pull this pin to high for read mode and pull it to low for write mode. 16 R/W When 80XX interface mode is selected, this pin will be the write (WR ) input. Data write operation is initiated when this pin is pulled low and the CS is pulled low. Read / write enable or read This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as the 17 E/RD enable (E) signal. Read / write operation is initiated when this pin is pulled high and the CS is pulled low. When connecting to an 80XX-microprocessor, this pin receives the read (RD ) signal. Data read operation is initiated when this pin is pulled low and CS is pulled low. Host data input / output bus These pins are 8-bit bi-directional data bus to be connected to the microprocessors data bus. When serial mode 2 18 to 25 D0 to D7 is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. When I C mode is selected, D2 and D1 should be tired together and serve as SDA and SDA in application and D0 is the serial out in clock input SCL. Current reference for brightness adjustment 26 I This pin is segment current reference pin. A resistor should be connected between this pin and V . Set the current REF SS lower than 12.5 A. Voltage output high level for COM signal 27 V This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between COMH this pin and V . SS Power supply for OEL panel 28 V This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this CC pin and V when the converter is used. It must be connected to external source when the converter is not used. SS Ground of analog circuit 29 V LSS This is an analog ground pin. It should be connected to V externally. SS Reserved pin (supporting pin) 30 NC (GND) The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground. Revision: 14-Dec-16 Document Number: 37902 2 For technical questions, contact: displays vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000