OLED-128O064H-GPP3N00000 www.vishay.com Vishay 128 x 64 Graphic OLED FEATURES Type: graphic Display format: 128 x 64 dots Built-in controller: SSD1309ZC Duty cycle: 1/64 +3 V power supply Interface: 6800, option 8080 and SPI With polarizer Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 MECHANICAL DATA ABSOLUTE MAXIMUM RATINGS ITEM STANDARD VALUE UNIT STANDARD VALUE ITEM SYMBOL UNIT Module dimension 60.50 x 37.00 x 2.15 MIN. MAX. Viewing area 57.01 x 28.91 Supply voltage V -0.3 4 (1)(2) DD for logic Active area 55.01 x 27.49 V mm Supply voltage V 015 Dot size 0.40 x 0.40 CC (1)(2) for display Dot pitch 0.43 x 0.43 Operating T -40 +80 OP temperature Mounting hole n/a C Storage T -40 +80 STG temperature Notes (1) All the above voltages are on the basis of V = 0 V. SS (2) When this module is used beyond the above absolute maximum ratings, permanent breakage of the module may occur. Also, for normal operations, it is desirable to use this module under the conditions according to section 6 Electrical Characteristics. If this module is used beyond these conditions, malfunctioning of the module can occur and the reliability of the module may deteriorate. ELECTRICAL CHARACTERISTICS STANDARD VALUE ITEM SYMBOL CONDITION UNIT MIN. TYP. MAX. Supply voltage for logic V - 2.8 3.0 3.3 DD Supply voltage for display V - 121315 CC Input high voltage V - 0.8 V -- IH DD V Input low voltage V - - - 0.2 V IL DD Output high voltage V - 0.9 V -- OH DD Output low voltage V - - - 0.1 V OL DD 50 % check board operating current I V = 13.0 V 15 18 22 mA CC CC OPTIONS EMITTING COLOR YELLOW GREEN RED BLUE WHITE - Yes --- Revision: 29-Jun-17 Document Number: 37913 1 For technical questions, contact: displays vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 OLED-128O064H-GPP3N00000 www.vishay.com Vishay INTERFACE PIN FUNCTION PIN NO. SYMBOL FUNCTION 1 NC (GND) No connection. Power supply for panel driving voltage. This is also the most positive power voltage supply 2V CC pin. COM signal deselected voltage level. 3V COMH A capacitor should be connected between this pin and V . SS This pin is the segment output current reference pin. 4I REF I is supplied externally. REF These pins are bi-directional data bus connecting to the MCU data bus. Unused pins are recommended to tie low. When serial interface mode is selected, D0 will be the serial clock input: SCLK D1 will be the 5 to 12 D0 to D7 serial data input: SDIN and D2 should be kept NC. 2 When I C mode is selected, D2, D1 should be tied together and serve as SDA , SDA in OUT IN application and D0 is the serial clock input, SCL. This pin is MCU interface input. When 6800 interface mode is selected, this pin will be used as the enable (E) signal. Read / write operation is initiated when this pin is pulled high and the chip is selected. 13 E / RD When 8080 interface mode is selected, this pin receives the read (RD ) signal. Read operation is initiated when this pin is pulled low and the chip is selected. 2 When serial or I C interface is selected, this pin must be connected to V . SS This pin is read / write control input pin connecting to the MCU interface. When 6800 interface mode is selected, this pin will be used as read / write (R / W ) selection input. Read mode will be carried out when this pin is pulled high and write mode when 14 R / W low. When 8080 interface mode is selected, this pin will be the write (WR ) input. Data write operation is initiated when this pin is pulled low and the chip is selected. 2 When serial or I C interface is selected, this pin must be connected to V . SS This pin is data / command control pin connecting to the MCU. When the pin is pulled high, the data at D 7:0 will be interpreted as data. 15 D / C When the pin is pulled low, the data at D 7:0 will be transferred to a command register. 2 In I C mode, this pin acts as SA0 for slave address selection. When 3-wire serial interface is selected, this pin must be connected to V . SS This pin is reset signal input. 16 RES When the pin is pulled low, initialization of the chip is executed. Keep this pin pull high during normal operation. This pin is the chip select input connecting to the MCU. 17 CS The chip is enabled for MCU communication only when CS is pulled low (active low). 18 NC No connection. MCU bus interface selection pins. Select appropriate logic setting as described in the following 19 BS2 table. BS2, BS1 and BS0 are pin select BS1 BS2 2 IC10 4-wire serial 0 0 8-bit 68XX parallel 0 1 20 BS1 8-bit 80XX parallel 1 1 Notes 0 is connected to V SS 1 is connected to V DD 21 V Power supply pin for core logic operation. DD 22 to 29 NC No connection. 30 V Ground. SS 31 NC (GND) No connection. Revision: 29-Jun-17 Document Number: 37913 2 For technical questions, contact: displays vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000