33 3 TSMP58000 www.vishay.com Vishay Semiconductors IR Sensor Module for Remote Control Systems FEATURES Photo detector and preamplifier in one package AC coupled response from 20 kHz to 60 kHz, all data formats Improved shielding against electrical field disturbance TTL and CMOS compatibility Output active low 1 22 Supply voltage 2.5 V to 5.5 V, typically the device 33 19026 works in the range between 2.0 V and 5.5 V Carrier out signal for code learning functions DESIGN SUPPORT TOOLS AVAILABLE Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 3D Models DESCRIPTION The TSMP58000 is a miniaturized sensor for receiving the MECHANICAL DATA modulated signal of infrared remote control systems. A PIN Pinning: diode and preamplifier are assembled on a lead frame, the 1 = carrier OUT, 2 = GND, 3 = V S epoxy package is designed as an IR filter. The modulate d output signal, carrier out, can be used for code learning applications. This component has not been qualified according to automotive specifications. PARTS TABLE Carrier frequency 20 kHz to 60 kHz TSMP58000 Package Minicast Pinning 1 = carrier OUT, 2 = GND, 3 = V S Dimensions (mm) 5.0 W x 6.95 H x 4.8 D Mounting Leaded Application Code learning BLOCK DIAGRAM APPLICATION CIRCUIT R = 100 V 1 S Transmitte r TSMPxxxx with 3 V + V S C = S 1 R = 2 TSALxxxx 4.7 F 4.7 k C 1 Carrier out OUT V O TIA Amp Signal shaping GND GND 2 GND R + C recommended to suppress power supply 1 1 disturbances. 19746 R recommended to get faster slopes and a correct 2 high level of the output pulses. Rev. 1.4, 23-Apr-2019 Document Number: 82485 1 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 DD D Circuit TSMP58000 www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage (pin 3) V -0.3 to +6 V S Output voltage (pin 1) V -0.3 to (V + 0.3) V O S Output current (pin 1) I 5mA O Junction temperature T 100 C j Storage temperature range T -25 to +85 C stg Operating temperature range T -25 to +85 C amb Soldering temperature t 10 s, 1 mm from case T 260 C sd Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating onl y and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specificatio n is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS CARRIER OUT (T = 25 C, unless otherwise specified, V = 3 V) amb S PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT Supply current (pin 3) E = 0 I 0.55 0.7 0.9 mA v SD Supply voltage V 2.5 - 5.5 V S E = 0, test signal see Fig. 1, v Transmission distance d- 1.8 - m IR diode TSAL6200, I = 50 mA F Output voltage low (pin 1) I = 0.5 mA, test signal see Fig. 1 V -- 250 mV OSL OSL 2 Minimum irradiance V = 3 V, (20 kHz to 60 kHz) E -12 25 mW/m S e min. 2 Maximum irradiance Test signal see Fig. 1, (20 kHz to 60 kHz) E 50 80 - W/m e max. Directivity Angle of half transmission distance - 45 - deg 1/2 f = 20 kHz to 60 kHz, N input burst input burst C input burst 2 2 Output accuracy E = 25 mW/m to 50 W/m , carrier length length counts e length test signal see Fig. 1, BER 2% pulses - 1 cycle + 1 cycle TYPICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb Carrier cycle (26.3 s in case of 38 kHz) Optical burst (input signal) Delay time t d Output voltage Fig. 1 - Testsignal Rev. 1.4, 23-Apr-2019 Document Number: 82485 2 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000