333 3 TSMP6000 www.vishay.com Vishay Semiconductors IR Sensor Module for Remote Control Systems FEATURES Photo detector and preamplifier in one package AC coupled response from 20 kHz to 60 kHz, all data formats Improved shielding against electrical field disturbance 4 TTL and CMOS compatibility 3 2 Output active low 1 16797 Supply voltage 2.5 V to 5.5 V, typically the device works in the range between 2.0 V and 5.5 V DESIGN SUPPORT TOOLS AVAILABLE Carrier out signal for code learning functions Material categorization: for definitions of compliance 3D Models please see www.vishay.com/doc 99912 DESCRIPTION MECHANICAL DATA The TSMP6000 is a miniaturized sensor for receiving various Pinning: kinds of modulated IR signals. A PIN diode and preamplifier 1 = GND, 2 = N.C., 3 = V , 4 = OUT S are assembled on a lead frame, the epoxy package is designed as an IR filter. The modulated output signal, carrier ORDERING CODE out, can be used for code learning applications. Taping: This component has not been qualified according to TSMP6000TT - top view taped automotive specifications. TSMP6000TR - side view taped PARTS TABLE Carrier frequency 20 kHz to 60 kHz TSMP6000 Package Panhead Pinning 1 = GND, 2 = N.C., 3 = V , 4 = OUT S Dimensions (mm) 7.5 W x 5.3 H x 4.0 D Mounting SMD Application Code learning BLOCK DIAGRAM APPLICATION CIRCUIT 19750-2 R = 100 V 1 S Transmitte r TSMPxxxx 3 V S with + V C = S 1 R = 2 TSALxxxx 4.7 F 4.7 k 4 Carrier out C OUT TIA Amp Signal shaping V O GND GND 1 GND R + C recommended to suppress power supply disturbances. 1 1 19746-1 R recommended to get faster slopes and a correct high level of the 2 output pulses. Rev. 1.9, 29-Aug-2019 Document Number: 82620 1 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 DDD D Circuit TSMP6000 www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage (pin 3) V -0.3 to +6 V S Output voltage (pin 4) V -0.3 to (V + 0.3) V O S Output current (pin 4) I 5mA O Junction temperature T 100 C j Storage temperature range T -25 to +85 C stg Operating temperature range T -25 to +85 C amb Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating onl y and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specificatio n is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS CARRIER OUT (T = 25 C, unless otherwise specified, V = 3 V) amb S PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT Supply current (pin 3) E = 0 I 0.55 0.7 0.9 mA v SD Supply voltage V 2.5 - 5.5 V S E = 0, test signal see Fig. 1, v Transmission distance d- 1.8 - m IR diode TSAL6200, I = 50 mA F Output voltage low (pin 4) I = 0.5 mA, test signal see Fig. 1 V -- 250 mV OSL OSL 2 Minimum irradiance V = 3 V, (20 kHz to 60 kHz) E -12 25 mW/m S e min. 2 Maximum irradiance Test signal see Fig. 1, (20 kHz to 60 kHz) E 50 80 - W/m e max. Directivity Angle of half transmission distance - 50 - deg 1/2 f = 20 kHz to 60 kHz, N Input burst Input burst C Input burst 2 2 Output accuracy E = 25 mW/m to 50 W/m , carrier length length counts e length test signal see Fig. 1, BER 2% pulses -1 cycle +1 cycle TYPICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb Carrier cycle (26.3 s in case of 38 kHz) Optical burst (input signal) Delay time t d Output voltage Fig. 1 - Testsignal Rev. 1.9, 29-Aug-2019 Document Number: 82620 2 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000