TSOP321.., TSOP323.., TSOP325.., TSOP341.., TSOP343..,
www.vishay.com
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
FEATURES
Very low supply current
Photo detector and preamplifier in one package
Internal filter for PCM frequency
Improved shielding against EMI
Supply voltage: 2.5 V to 5.5 V
Improved immunity against ambient light
Insensitive to supply voltage ripple and noise
1
22
Material categorization:
33 16672
for definitions of compliance please see
www.vishay.com/doc?99912
click logo to get started
DESIGN SUPPORT TOOLS
DESCRIPTION
Models
These products are miniaturized receivers for infrared
Available
remote control systems. A PIN diode and a preamplifier are
assembled on a lead frame, the epoxy package contains an
MECHANICAL DATA
IR filter. The demodulated output signal can be directly
Pinning for TSOP341.., TSOP343.., TSOP345..:
connected to a microprocessor for decoding.
1 = OUT, 2 = GND, 3 = V
S
The TSOP323.., TSOP343..series devices are optimized to
Pinning for TSOP321.., TSOP323.., TSOP325..:
suppress almost all spurious pulses from energy saving
lamps like CFLs. AGC3 may also suppress some data
1 = OUT, 2 = V , 3 = GND
S
signals if continuously transmitted.
The TSOP321.., TSOP341.. series are provided primarily for
compatibility with old AGC1 designs. New designs should
prefer the TSOP323.., TSOP343.. series containing the
newer AGC3. The TSOP325.., TSOP345.. series contain a
very robust AGC5. This series should only be used for
critically noisy environments.
These components have not been qualified according to
automotive specifications.
PARTS TABLE
LEGACY, FOR SHORT BURST NOISY ENVIRONMENTS AND VERY NOISY ENVIRONMENTS
AGC
REMOTE CONTROLS (AGC1) SHORT BURSTS (AGC3) AND SHORT BURSTS (AGC5)
30 kHz TSOP34130 TSOP32130 TSOP34330 TSOP32330 TSOP34530 TSOP32530
33 kHz TSOP34133 TSOP32133 TSOP34333 TSOP32333 TSOP34533 TSOP32533
(1)(6) (1)(6)
36 kHz TSOP34136 TSOP32136 TSOP34336 TSOP32336 TSOP34536 TSOP32536
Carrier
(2)(3)(4)(5) (2)(3)(4)(5)
frequency
38 kHz TSOP34138 TSOP32138 TSOP34338 TSOP32338 TSOP34538 TSOP32538
40 kHz TSOP34140 TSOP32140 TSOP34340 TSOP32340 TSOP34540 TSOP32540
56 kHz TSOP34156 TSOP32156 TSOP34356 TSOP32356 TSOP34556 TSOP32556
Package Mold
1 = OUT, 1 = OUT, 2 = V , 1 = OUT, 1 = OUT, 2 = V , 1 = OUT, 1 = OUT, 2 = V ,
S S S
Pinning
2 = GND, 3 = V 3 = GND 2 = GND, 3 = V 3 = GND 2 = GND, 3 = V 3 = GND
S S S
Dimensions (mm) 6.0 W x 6.95 H x 5.6 D
Mounting Leaded
Application Remote control
(1) (2) (3) (4) (5) (6)
Best choice for MCIR Mitsubishi RECS-80 Code r-map XMP-1, XMP-2 RCMM
Rev. 1.7, 24-Sep-2018 Document Number: 82490
1
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP321.., TSOP323.., TSOP325.., TSOP341.., TSOP343..,
www.vishay.com
Vishay Semiconductors
BLOCK DIAGRAM APPLICATION CIRCUIT
16833-13
17170-11
R
1
3
Transmitter
IR receiver
with
30 k V
+ V
S
S
TSALxxxx
C
1
1
C
OUT
Band Demo-
Input AGC
pass
dulator
V
O
GND
GND
2
PIN
Control circuit
R and C recommended to reduce supply ripple for V < 2.8 V
1 1 S
ABSOLUTE MAXIMUM RATINGS
PARAMETER TEST CONDITION SYMBOL VALUE UNIT
Supply voltage V -0.3 to +6 V
S
Supply current I 3mA
S
Output voltage V -0.3 to (V + 0.3) V
O S
Output current I 5mA
O
Junction temperature T 100 C
j
Storage temperature range T -25 to +85 C
stg
Operating temperature range T -25 to +85 C
amb
Power consumption T 85 C P 10 mW
amb tot
Soldering temperature t 10 s, 1 mm from case T 260 C
sd
Note
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability
ELECTRICAL AND OPTICAL CHARACTERISTICS (T = 25 C, unless otherwise specified)
amb
PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT
E = 0, V = 3.3 V I 0.27 0.35 0.45 mA
v S SD
Supply current
E = 40 klx, sunlight I -0.45- mA
v SH
Supply voltage V 2.5 - 5.5 V
S
E = 0, test signal see Fig. 1,
v
Transmission distance IR diode TSAL6200, d- 30 - m
I = 50 mA
F
2
I = 0.5 mA, E = 0.7 mW/m ,
OSL e
Output voltage low V - - 100 mV
OSL
test signal see Fig. 1
Pulse width tolerance:
2
Minimum irradiance t - 5/f < t < t + 6/f , E - 0.08 0.15 mW/m
pi o po pi o e min.
test signal see Fig. 1
t - 5/f < t < t + 6/f ,
pi o po pi o
2
Maximum irradiance E 30 - - W/m
e max.
test signal see Fig. 1
Angle of half transmission
Directivity - 45 -
1/2
distance
Rev. 1.7, 24-Sep-2018 Document Number: 82490
2
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Circuit