TSOP36256TT Vishay

333 3 TSOP362.., TSOP364.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES Very low supply current Photo detector and preamplifier in one package Internal filter for PCM frequency Supply voltage range: 2.5 V to 5.5 V Improved immunity against modulated light sources 4 3 Insensitive to supply voltage ripple and noise 2 1 Capable of side or top view 16797 Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 LINKS TO ADDITIONAL RESOURCES MECHANICAL DATA Product Page 3D Models Calculators Marking Pinning: 1 = GND, 2 = N.C., 3 = V , 4 = OUT S DESCRIPTION ORDERING CODE The TSOP36... series are miniaturized SMD IR receiver modules for infrared remote control systems. A PIN diode Taping: and a preamplifier are assembled on a leadframe, the epoxy TSOP36...TT - top view taped, 1190 pcs/reel package contains an IR filter. TSOP36...TR - side view taped, 1120 pcs/reel The demodulated output signal can be directly connected to a microprocessor for decoding. The TSOP364.. series devices are optimized to suppress BLOCK DIAGRAM almost all spurious pulses from energy saving lamps lik e 3 CFLs. The AGC4 used in the TSOP364.. may suppress V some data signals. The TSOP362.. series are provided S 30 k primarily for compatibility with old AGC2 designs. New 4 designs should prefer the TSOP364.. series containing the OUT newer AGC4. Band Demo- Input AGC dulator pass These components have not been qualified according to automotive specifications. 1 2 PIN GND Control circuit 16839 APPLICATION CIRCUIT 17170-11 R 1 Transmitter IR receiver with V + V S S TSALxxxx C 1 C OUT V O GND GND R and C recommended to reduce supply ripple for V < 2.8 V 1 1 S Rev. 1.9, 26-Mar-2021 Document Number: 82568 1 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 DDD D Circuit TSOP362.., TSOP364.. www.vishay.com Vishay Semiconductors PARTS TABLE LEGACY, FOR RECOMMENDED FOR AGC LONG BURST REMOTE CONTROLS (AGC2) LONG BURST CODES (AGC4) 30 kHz TSOP36230 TSOP36430 33 kHz TSOP36233 TSOP36433 (1)(2)(3) 36 kHz TSOP36236 TSOP36436 Carrier frequency (4)(5) 38 kHz TSOP36238 TSOP36438 40 kHz TSOP36240 TSOP36440 (6)(7) 56 kHz TSOP36256 TSOP36456 Package Panhead Pinning 1 = GND, 2 = N.C., 3 = V , 4 = OUT S Dimensions (mm) 7.5 W x 5.3 H x 4.0 D Mounting SMD Application Remote control (1) (2) (3) (4) (5) (6) (7) Best choice for RC-5 RC-6 Panasonic NEC Sharp r-step Thomson RCA Narrow optical filter: www.vishay.com/doc 81590 Special options Wide optical flter: www.vishay.com/doc 82726 ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage (pin 3) V -0.3 to +6 V S Supply current (pin 3) I 3mA S Output voltage (pin 4) V -0.3 to (V + 0.3) V O S Output current (pin 4) I 5mA O Junction temperature T 100 C j Storage temperature range T -25 to +85 C stg Operating temperature range T -25 to +85 C amb Power consumption T 85 C P 10 mW amb tot Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating onl y and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specificatio n is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT E = 0, V = 3.3 V I 0.27 0.35 0.45 mA v S SD Supply current E = 40 klx, sunlight I -0.45 - mA v SH Supply voltage V 2.5 - 5.5 V S E = 0, test signal see Fig. 1, v Transmission distance IR diode TSAL6200, d- 24 - m I = 50 mA F 2 I = 0.5 mA, E = 0.7 mW/m , OSL e Output voltage low V - - 100 mV OSL test signal see Fig. 1 Pulse width tolerance: 2 Minimum irradiance t - 5/f < t < t + 6/f , E - 0.12 0.25 mW/m pi o po pi o e min. test signal see Fig. 1 t - 5/f < t < t + 6/f , pi o po pi o 2 Maximum irradiance E 30 - - W/m e max. test signal see Fig. 1 Angle of half transmission Directivity - 50 - 1/2 distance Rev. 1.9, 26-Mar-2021 Document Number: 82568 2 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000