333 3 TSOP381.., TSOP383.., TSOP385.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES Very low supply current Photo detector and preamplifier in one package Internal filter for PCM frequency Supply voltage: 2.5 V to 5.5 V Improved immunity against ambient light Insensitive to supply voltage ripple and noise 1 Material categorization: 22 for definitions of compliance please see 33 19026 www.vishay.com/doc 99912 LINKS TO ADDITIONAL RESOURCES MECHANICAL DATA Pinning for TSOP381.., TSOP383.., TSOP385..: Product Page 3D Models Calculators Marking Packages 1 = OUT, 2 = GND, 3 = V S Holders Bends and Cuts ORDERING CODE TSOP38... - 1500 pieces in bags DESCRIPTION These products are miniaturized receivers for infrared BLOCK DIAGRAM remote control systems. A PIN diode and a preamplifier are 16833-13 assembled on a lead frame, the epoxy package contains a n IR filter. The demodulated output signal can be directly 3 connected to a microprocessor for decoding. 30 k The TSOP383.. series devices are optimized to suppress 1 almost all spurious pulses from energy saving lamps lik e CFLs. AGC3 may also suppress some data signals if Band Demo- Input AGC pass dulator continuously transmitted. The TSOP381.. series are provided primarily for 2 compatibility with old AGC1 designs. New designs should PIN Control circuit prefer the TSOP383.. series containing the newer AGC3. The TSOP385.. series contain a very robust AGC5. This series should only be used for critically noisy environments. These components have not been qualified according to APPLICATION CIRCUIT automotive specifications. 17170-11 R 1 Transmitter IR receiver with V + V S S TSALxxxx C 1 C OUT V O GND GND R and C recommended to reduce supply ripple for V < 2.8 V 1 1 S Rev. 1.7, 09-Aug-2021 Document Number: 81743 1 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 DDD D Circuit TSOP381.., TSOP383.., TSOP385.. www.vishay.com Vishay Semiconductors PARTS TABLE LEGACY, FOR SHORT BURST NOISY ENVIRONMENTS AND VERY NOISY ENVIRONMENTS AGC REMOTE CONTROLS (AGC1) SHORT BURSTS (AGC3) AND SHORT BURSTS (AGC5) 30 kHz TSOP38130 TSOP38330 TSOP38530 33 kHz TSOP38133 TSOP38333 TSOP38533 (1)(6) 36 kHz TSOP38136 TSOP38336 TSOP38536 Carrier frequency (2)(3)(4)(5) 38 kHz TSOP38138 TSOP38338 TSOP38538 40 kHz TSOP38140 TSOP38340 TSOP38540 56 kHz TSOP38156 TSOP38356 TSOP38556 Package Minicast Pinning 1 = OUT, 2 = GND, 3 = V S Dimensions (mm) 5.0 W x 6.95 H x 4.8 D Mounting Leaded Application Remote control (1) (2) (3) (4) (5) (6) Best choice for MCIR Mitsubishi RECS-80 Code r-map XMP-1, XMP-2 RCMM Special options Low voltage option: www.vishay.com/doc 82382 ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage V -0.3 to +6 V S Supply current I 3mA S Output voltage V -0.3 to (V + 0.3) V O S Output current I 5mA O Junction temperature T 100 C j Storage temperature range T -25 to +85 C stg Operating temperature range T -25 to +85 C amb Power consumption T 85 C P 10 mW amb tot Soldering temperature t 10 s, 1 mm from case T 260 C sd Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating onl y and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specificatio n is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT E = 0, V = 3.3 V I 0.27 0.35 0.45 mA v S SD Supply current E = 40 klx, sunlight I -0.45- mA v SH Supply voltage V 2.5 - 5.5 V S E = 0, test signal see Fig. 1, v Transmission distance d- 24 - m IR diode TSAL6200, I = 50 mA F 2 Output voltage low I = 0.5 mA, E = 0.7 mW/m , test signal see Fig. 1 V -- 100 mV OSL e OSL Pulse width tolerance: 2 Minimum irradiance E - 0.12 0.25 mW/m e min. t - 5/f < t < t + 6/f , test signal see Fig. 1 pi o po pi o 2 Maximum irradiance t - 5/f < t < t + 6/f , test signal see Fig. 1 E 30 - - W/m pi o po pi o e max. Directivity Angle of half transmission distance - 45 - 1/2 Rev. 1.7, 09-Aug-2021 Document Number: 81743 2 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000
