TSOP77256TR Vishay

333 3 TSOP772.., TSOP774.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES Improved immunity against HF and RF noise Low supply current Photo detector and preamplifier in one package Internal filter for PCM frequency 44 Supply voltage: 2.5 V to 5.5 V 33 Improved immunity against optical noise 22 11 Capable of side or top view Insensitive to supply voltage ripple and noise Two lenses for high sensitivity and wide receiving angle 2095320953 Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 LINKS TO ADDITIONAL RESOURCES MECHANICAL DATA Product Page 3D Models Calculators Marking Pinning: 1, 4 = GND, 2 = V , 3 = OUT S DESCRIPTION ORDERING CODE The TSOP77... series are miniaturized SMD IR receiver modules for infrared remote control systems. Two PIN Taping: diodes and a preamplifier are assembled on a leadframe, TSOP77...TT - top view taped, 2200 pcs/reel the epoxy package contains an IR filter. The demodulated TSOP77...TR - side view taped, 2300 pcs/reel output signal can be directly connected to a microprocessor for decoding. The TSOP774.. series devices are optimized to suppress BLOCK DIAGRAM almost all spurious pulses from Wi-Fi and CFL sources. 2 They may suppress some data signals if continuously V transmitted. S 30 k The TSOP772.. series devices are provided primarily for 3 compatibility with old AGC2 designs. New designs should OUT Band Demo- prefer the TSOP774.. series containing the newer AGC4. Input AGC pass dulator These components have not been qualified according to 1, 4 automotive specifications. PIN Control circuit GND 20445-1 APPLICATION CIRCUIT 17170-11 R 1 Transmitter IR receiver with V + V S S TSALxxxx C 1 C OUT V O GND GND R and C recommended to reduce supply ripple for V < 2.8 V 1 1 S Rev. 2.1, 29-Mar-2021 Document Number: 82471 1 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 DDD D Circuit TSOP772.., TSOP774.. www.vishay.com Vishay Semiconductors PARTS TABLE LEGACY, FOR RECOMMENDED FOR AGC LONG BURST REMOTE CONTROLS (AGC2) LONG BURST CODES (AGC4) 30 kHz TSOP77230 TSOP77430 33 kHz TSOP77233 TSOP77433 (1)(2)(3) 36 kHz TSOP77236 TSOP77436 Carrier frequency (4)(5) 38 kHz TSOP77238 TSOP77438 40 kHz TSOP77240 TSOP77440 (6)(7) 56 kHz TSOP77256 TSOP77456 Package Heimdall Pinning 1, 4 = GND, 2 = V , 3 = OUT S Dimensions (mm) 6.8 W x 3.0 H x 3.2 D Mounting SMD Application Remote control (1) (2) (3) (4) (5) (6) (7) Best choice for RC-5 RC-6 Panasonic NEC Sharp r-step Thomson RCA Extended temperature range: www.vishay.com/doc 82738 Special options Narrow optical filter: www.vishay.com/doc 81590 Wide optical flter: www.vishay.com/doc 82726 ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage V -0.3 to +6 V S Supply current I 5mA S Output voltage V -0.3 to (V + 0.3) V O S Output current I 5mA O Junction temperature T 100 C j Storage temperature range T -25 to +85 C stg Operating temperature range T -25 to +85 C amb Power consumption T 85 C P 10 mW amb tot Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating onl y and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specificatio n is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT Supply voltage V 2.5 - 5.5 V S V = 5 V, E = 0 I 0.55 0.7 0.9 mA S v SD Supply current E = 40 klx, sunlight I -0.8 - mA v SH E = 0, IR diode TSAL6200, v Transmission distance d- 18 - m I = 50 mA, test signal see Fig. 1 F 2 Output voltage low I = 0.5 mA, E = 0.7 mW/m , test signal see Fig. 1 V - - 100 mV OSL e OSL Pulse width tolerance: 2 Minimum irradiance E -0.2 0.4 mW/m e min. t - 5/f < t < t + 6/f test signal see Fig. 1 pi o po pi o, 2 Maximum irradiance t - 5/f < t < t + 6/f , test signal see Fig. 1 E 50 - - W/m pi o po pi o e max. Directivity Angle of half transmission distance - 50 - 1/2 Rev. 2.1, 29-Mar-2021 Document Number: 82471 2 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000