VO1263AAC, VO1263AACTR, VO1263AB www.vishay.com Vishay Semiconductors Dual Photovoltaic MOSFET Driver Solid-State Relay FEATURES DIP 8675 High open circuit voltage, up to 14.6 V typical High short circuit current, up to 42 A typical Isolation test voltage 5300 V RMS Logic compatible input High reliability Material categorization: for definitions of 1324 compliance please see www.vishay.com/doc 99912 SMD - Control 1 - Output 1 APPLICATIONS + Control 1 + Output 1 High side driver - Control 2 - Output 2 Solid-state relays + Control 2 + Output 2 Floating power supply i179034 2 Power control DESIGN SUPPORT TOOLS AVAILABLE Data acquisition ATE Related Isolated switching Documents AGENCY APPROVALS DESCRIPTION UL The VO1263AB and VO1263AAC photovoltaic MOSFET driver consists of two LEDs optically coupled to two DIN EN 60747-5 (VDE 0884-5) photodiode arrays. The photodiode array provides a floating BSI source with adequate voltage and current to drive high CQC power MOSFET transistors. Optical coupling provides a high I/O isolation voltage. In order to turn the MOSFET off, FIMKO an external resistance (gate-to-source) is required for gate discharge. ORDERING INFORMATION SMD DIP V O 1263 T R PART NUMBER ELECTR. PACKAGE TAPE AND > 0.1 mm 7.62 mm VARIATION CONFIG. REEL PACKAGE UL, VDE, BSI, CQC, FIMKO SMD-8 VO1263AAC SMD-8, tape and reel VO1263AACTR DIP-8 VO1263AB ABSOLUTE MAXIMUM RATINGS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL VALUE UNIT SSR LED input ratings continuous forward current I 50 mA F LED input ratings reverse voltage I 10 A V 5.0 V R R Photodiode array reverse voltage I 2.0 A V 100 V R R Ambient operating temperature range T -40 to +100 C amb Storage temperature range T -40 to +150 C stg Pin soldering temperature t = 7.0 s max. T 270 C sld Note Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability Rev. 2.0, 15-Mar-2019 Document Number: 84639 1 For technical questions, contact: optocoupleranswers vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 VO1263AAC, VO1263AACTR, VO1263AB www.vishay.com Vishay Semiconductors ELECTRICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT LED forward voltage I = 10 mA V 1.2 1.3 1.6 V F F Detector reverse voltage I = 2.0 A V - 350 - V R R(PDA) I = 5.0 mA V - 13.73 - V F OC I = 10 mA V 10.3 14.27 16.5 V F OC Open circuit voltage (pins 5, 6 or 7, 8) I = 15 mA V - 14.50 - V F OC I = 20 mA V - 14.70 - V F OC I = 30 mA V - 14.94 - V F OC I = 5.0 mA I 2.7 4.47 - A F SC I = 10 mA I 79.8 - A F SC Short circuit current (pins 5, 6 or 7, 8) I = 15 mA I 11 15.33 - A F SC I = 20 mA I 15 20.97 - A F SC I = 30 mA I 21 32.4 - A F SC Note Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluations. Typical values are for information only and are not part of the testing requirements SWITCHING CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT (1) Turn-on time I = 20 mA t -16 - s F on (1) Turn-off time I = 20 mA t - 472 - s F off Note (1) f = 1.0 kHz, pulse width = 100 s, load (R ) = 1.0 M, 15 pF measured at 90 % rated voltage (t ), 10 % rated voltage (t ). Actuation speed L on off depends upon the external t and t circuitry and the capacitance of the MOSFET on off SAFETY AND INSULATION RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Climatic classification According to IEC 68 part 1 40 / 100 / 21 Pollution degree According to DIN VDE 0109 2 Comparative tracking index Insulation group IIIa CTI 175 Maximum rated withstanding isolation voltage According to UL1577, t = 1 min V 5300 V ISO RMS Maximum transient isolation voltage According to DIN EN 60747-5-5 V 8000 V IOTM peak Maximum repetitive peak isolation voltage According to DIN EN 60747-5-5 V 890 V IORM peak Output safety power P 700 mW SO Input safety current I 300 mA SI Input safety temperature T 175 C S Creepage distance 7mm DIP-8, SMD-8 Clearance distance 7mm Note This optocoupler is suitable for safe electrical insulation only within the safety ratings. Compliance with the safety ratings shall be ensure d by means of suitable protective circuits Rev. 2.0, 15-Mar-2019 Document Number: 84639 2 For technical questions, contact: optocoupleranswers vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000