VOM452, VOM453 www.vishay.com Vishay Semiconductors Analog High Speed Coupler, High Noise Immunity, 1 MBd, SOP-5 Package FEATURES Surface mountable A 1 6 V CC Industry standard SOP-5 footprint 5 C Compatible with infrared vapor phase reflow 4 C 3 E and wave soldering processes Isolation test voltage, 3750 V RMS Very high common mode transient immunity: 20409-1 15 000 V/s at V = 1500 V guaranteed (VOM453) CM High speed: 1 MBd DESCRIPTION TTL compatible The VOM452 and VOM453, high speed optocouplers, each Open collector output consists of a GaAlAs infrared emitting diode, optically coupled with an integrated photo detector and a high speed Material categorization: for definitions of compliance transistor. The photo detector is junction isolated from the please see www.vishay.com/doc 99912 transistor to reduce miller capacitance effects. The open APPLICATIONS collector output function allows circuit designers to adjust the load conditions when interfacing with different logic Fieldbus communication and control systems such as TTL, CMOS, etc. Logic ground isolation Because the VOM452 and VOM453 have a Faraday shield Analog signal ground isolation on the detector chip, it can also reject and minimize high Replace pulse transformers input to output common mode transient voltages. There is no base connection, further reducing the potential electrical IPM (intelligent power module) drivers noise entering the package. AGENCY APPROVALS The VOM452 and VOM453 are packaged in industry standard SOP-5 packages and are suitable for surface UL1577 mounting. cUL This an ideal solution for Industrial communication bus DIN EN 60747-5-5 (VDE 0884-5) available with option 1 isolation, as well as isolated drive circuit applications such as IPM (intelligent power module) drivers. ORDERING INFORMATION SOP-5 VO M 4 5 T 7.21 mm PART NUMBER AGENCY CERTIFIED/PACKAGE CMTI (kV/s) UL, cUL 1 15 SOP-5 VOM452T VOM453T UL, cUL, VDE 1 15 SOP-5 VOM452-X001T VOM453-X001T Notes For additional information on the available options refer to option information. The product is available only on tape and reel. Rev. 1.6, 31-May-16 Document Number: 81587 1 For technical questions, contact: optocoupleranswers vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 VOM452, VOM453 www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL VALUE UNIT INPUT Reverse voltage V 3V R DC forward current I 25 mA F Surge forward current t 1 s, 300 pulses/s I 1A p FSM Power dissipation T 70 C P 45 mW amb diss OUTPUT Supply voltage V -0.5 to +30 V S Output voltage V -0.5 to +25 V O Output current I 8mA O Power dissipation T 70 C P 100 mW amb diss COUPLER Storage temperature range T -55 to +125 C stg Ambient temperature range T -55 to +100 C amb Junction temperature T 100 C j Soldering temperature t < 10 s max. 260 C Note Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability. ELECTRICAL CHARACTERISTICS (T = -40 C to +100 C, unless otherwise specified) amb PARAMETER TEST CONDITION PART SYMBOL MIN. TYP. MAX. UNIT INPUT Input forward voltage I = 16 mA V -1.4 1.8 V F F Input reverse current V = 3 V I - 0.5 10 A R R Input capacitance f = 1 MHz, V = 0 V, T = 25 C C -75- pF F amb IN Temperature coefficient of I = 16 mA V /T --1.7 - mV/C F F amb forward voltage OUTPUT Logic low supply current I = 16 mA, V = open, V = 15 V I - 200 - A F O CC CCL I = 0 mA, V = open, V = 15 V, F O CC I - 0.001 1 A CCH T = 25 C Logic high supply current amb I = 0 mA, V = open, V = 15 V I -- 2 A F O CC CCH I = 16 mA, V = 4.5 V, I = 3 mA, F CC O V - 0.15 0.4 V OL T = 25 C Logic low output voltage amb I = 16 mA, V = 15 V, I = 2.4 mA V -- 0.5 V F CC O OL I = 0 mA, V = V = 5.5 V, T = 25 C I - 0.003 0.5 A F O CC amb OH Logic high output current I = 0 mA, V = V = 15 V, T = 25 C I -0.01 1 A F O CC amb OH I = 0 mA, V = V = 15 V I - - 50 A F O CC OH COUPLER (1) Capacitance (input-output) f = 1 MHz, T = 25 C C -0.4 - pF amb IO Notes Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluation. Typical values are for information only and are not part of the testing requirements. All typical values are measured at T = 25 C. amb (1) A 0.1 F bypass capacitor connected between pins 4 and 6 is recommended. CURRENT TRANSFER RATIO (T = -40 C to +100 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT V = 0.5 V, I = 16 mA, V = 4.5 V 15 30 - O F CC (1)(2) Current transfer ratio CTR % V = 0.4 V, I = 16 mA, T = 25 C 20 - 50 O F amb Notes (1) Current transfer ratio in percent equals the ratio of output collector current (I ) to the forward LED input current (I ) times 100. O F (2) A 0.1 F bypass capacitor connected between pins 4 and 6 is recommended. All typical values are measured at T = 25 C. amb Rev. 1.6, 31-May-16 Document Number: 81587 2 For technical questions, contact: optocoupleranswers vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000