xppower.com 300 Watts PBM300 Series Worldwide Medical Approvals Single, Dual, Triple and Quad Outputs Power Fail Detect Remote On/Off U Channel and Enclosed Versions 150 Watt Convection cooled Rating 3 Year Warranty Specification Input General Input Voltage 90-264 VAC Efficiency 80% maximum Input Frequency 47-63 Hz Isolation 4000 VAC Input to Output 1500 VAC Input to Ground Input Current 4.7 A rms at 115 VAC, 500 VAC Output to Ground 2.3 A rms for 230 VAC Switching Frequency 70 kHz 10 kHz Inrush Current 30 A at 115 VAC, 60 A at 230 VAC cold start +25 C Signals Power fail detect, remote on/off 3 Power Factor 0.98 typical Power Density 5.08 W/In Earth Leakage Current 100 A max at 115 VAC/60 Hz Power Fail Detect AC OK = TTL logic high 220 A max at 230 VAC/50 Hz AC not OK = TTL logic low Input Protection Internal F6.3 A/250 V in line and MTBF 300 kHrs to MIL-HDBK-217F at neutral lines +25 C, GB Output Environmental Output Voltage See table Operating Temperature 0 C to +70 C, derate linearly from 100% power at +50 C to 50% power at +70 C Output Voltage Trim 5% for outputs 1 & 2 Cooling C versions have internal fan, Initial Set Accuracy 2% B versions are derated with convection Minimum Load See table and note 5 cooling or require 35 CFM (see note 4) Start Up Delay 2 s max Operating Humidity up to 95% RH, non-condensing Start Up Rise Time 18 ms typical Storage Temperature -40 C to +85 C Hold Up Time 12 ms min at full load and 110 VAC Operating Altitude 2500 m Drift 0.2% Shock Half sine pulse. acceleration 50 g, Line Regulation 0.2% max 11 ms duration, 3 shocks in each Load Regulation See note 6 direction, unpackaged, non-operating Transient Response 4% max deviation, recovery to within Vibration Sinusoidal 10-50 Hz, amplitude 0.15 mm, 1% in 500 s for a 25% load change 30 min/axis, unpackaged, non-operating Ripple & Noise 2% max pk-pk, 20 MHz bandwidth, with a 22 F electrolytic & a 0.47 F tantalum EMC & Safety capacitor Emissions EN55011 and FCC Class B conducted Overvoltage Protection 115-140% Vnom output 1 only, recycle & radiated input to reset Harmonic Currents EN61000-3-2, Class A Overtemperature Shutdown at +95 C (singles) or +105 C Voltage Flicker EN61000-3-3 Protection (multi-outputs) with auto recovery, measured internally ESD Immunity EN61000-4-2, level 3 Perf Criteria A Overload Protection 110-150% typical, auto recovery Radiated Immunity EN61000-4-3, level 3 Perf Criteria A Short Circuit Protection Trip and restart (Hiccup mode) EFT/Burst EN61000-4-4, level 3 Perf Criteria A Temperature 0.04%/C Surge EN61000-4-5, level 3 Perf Criteria A Coefficient Conducted Immunity EN61000-4-6, 3 V Perf Criteria A Remote Sense Compensates for up to 0.5 V drop Dips & Interruptions EN61000-4-11, 30% 10 ms, Remote On/Off On = Logic low or open circuit 60% 100 ms, >95% 5000 ms, Off = Logic high Perf Criteria A, A, B Safety Approvals EN60601-1, UL60601-1, CSA22.2 No. 601-1 per cUL AC DCAC DC PBM300 Models and Ratings (2) (2) (2) Output 1 Output 2 Output 3 Output 4 Output Model (4) (1) (3) (5) (6) (3) (6) (6) (6) Power Number Vnom Imin Imax Reg Vnom Imin Imax Reg Vnom Imax Reg Vnom Imax Reg 200 W 3.3 V 3.0 A 60.0 A 3% PBM300PS03-C 300 W 5.1 V 3.0 A 60.0 A 2% PBM300PS05-C 300 W 12.0 V 1.2 A 25.0 A 2% PBM300PS12-C 300 W 15.0 V 1.0 A 20.0 A 2% PBM300PS15-C 300 W 24.0 V 0.6 A 12.5 A 2% PBM300PS24-C 300 W 30.0 V 0.5 A 10.0 A 2% PBM300PS30-C 300 W 48.0 V 0.5 A 6.3 A 2% PBM300PS48-C 250 W 3.3 V 3.0 A 35.0 A 3% 5.1 V 2.0 A 22.0 A 2% 12.0 V 4.0 A 4% 12.0 V 4.0 A 4% PBM300PQ01-C 300 W 5.1 V 2.0 A 35.0 A 2% 12.0 V 1.0 A 10.0 A 2% 12.0 V 4.0 A 4% 5.1 V 4.0 A 4% PBM300PQ02-C 300 W 5.1 V 2.0 A 35.0 A 2% 15.0 V 0.8 A 8.0 A 2% 15.0 V 4.0 A 4% 24.0 V 2.5 A 4% PBM300PQ03-C 300 W 5.1 V 2.0 A 35.0 A 2% 12.0 V 1.0 A 10.0 A 2% 12.0 V 4.0 A 4% 12.0 V 4.0 A 4% PBM300PQ04-C 300 W 5.1 V 2.0 A 35.0 A 2% 12.0 V 1.0 A 10.0 A 2% 12.0 V 4.0 A 4% 24.0 V 2.5 A 4% PBM300PQ05-C 300 W 5.1 V 2.0 A 35.0 A 2% 12.0 V 1.0 A 10.0 A 2% 12.0 V 4.0 A 4% 15.0 V 4.0 A 4% PBM300PQ06-C 300 W 5.1 V 2.0 A 35.0 A 2% 24.0 V 0.5 A 5.0 A 2% 12.0 V 4.0 A 4% 12.0 V 4.0 A 4% PBM300PQ07-C 300 W 5.1 V 2.0 A 35.0 A 2% 24.0 V 0.5 A 5.0 A 2% 5.1 V 4.0 A 4% 15.0 V 4.0 A 4% PBM300PQ08-C 300 W 5.1 V 2.0 A 35.0 A 2% 12.0 V 1.0 A 10.0 A 2% 5.1 V 4.0 A 4% 24.0 V 2.5 A 4% PBM300PQ09-C 300 W 24.0 V 0.5 A 6.3 A 2% 12.0 V 1.0 A 10.0 A 2% 5.1 V 4.0 A 4% 12.0 V 4.0 A 4% PBM300PQ10-C 300 W 24.0 V 0.5 A 6.3 A 2% 12.0 V 1.0 A 10.0 A 2% 5.1 V 4.0 A 4% 24.0 V 2.5 A 4% PBM300PQ11-C 300 W 24.0 V 0.5 A 6.3 A 2% 12.0 V 1.0 A 10.0 A 2% 12.0 V 4.0 A 4% 12.0 V 4.0 A 4% PBM300PQ12-C 300 W 24.0 V 0.5 A 6.3 A 2% 24.0 V 0.5 A 5.0 A 2% 5.1 V 4.0 A 4% 15.0 V 4.0 A 4% PBM300PQ13-C 300 W 24.0 V 0.5 A 6.3 A 2% 24.0 V 0.5 A 5.0 A 2% 12.0 V 4.0 A 4% 12.0 V 4.0 A 4% PBM300PQ14-C Notes 1. For U-bracket format replace suffix -C with suffix -B . PBM300PS03 is rated 200 W with 35 CFM forced air cooling or 100 W 2. All auxiliary outputs are floating and can be connected externally for either convection-cooled. PBM300PQ01 is rated 250 W with 35 CFM forced air positive or negative output. cooling or 125 W with convection cooling. 3. Output 1 & 2 can be adjusted within 5% of their nominal voltage. 5. Zero minimum load for outputs 3 & 4. 10% minimum load required on out- 4. 300 W for C version with cover and fan assembly. 150 watts for B put 1 for all outputs to meet regulation. version with convection cooling (maximum current of output 1 & 2 derated 6. Total regulation includes initial tolerance, line regulation and load regulation. by 50%). 300 W for B version with 35 CFM forced air provided by user. Mechanical Details Model Number(s) Weight: 2.40 lb (1.09 kg) approx. for -B version, 2.75 lb (1.25g) approx. for -C version. PSXX PQXX Conn Pin 0.63 (16.0) 1 Line Line P1 2 Neutral Neutral 1.00 B B 3 Ground Ground (25.4) P2 1 OP1 OP1 1.75 P3 1 OP1 OP1 Return A A (44.45) 1 Signal Ground Signal Ground 10 2 +sense +sense OP1 0.94 (24.0) 3 -sense -sense OP1 4 PFD PFD P4 1.34 Voltage adj., single 5 Remote On/Off Remote On/Off (34.2) P4 A A 6 N.C. N.C. P2 P4 1 7 N.C. +sense OP2 4.50 B B P2 (114.3) 8 N.C. -sense OP2 P3 PCB 1.80 Voltage adj., multi 9 0V (fan) 0V (fan) P3 (45.7) P4 10 12V (fan) 12V (fan) 2.60 P5 P5 1 OP1 Return OP2 (66.0) P5 P6 1 OP1 Return OP2 Return 1 P1 P6 P6 1 n/a OP3 L B B 2 n/a OP3 Return 1 N A P7 A 3 n/a OP4 P7 G 4 n/a OP4 Return 3 Multi Notes Single 0.95 (24.1) Output 5.70 (144.8) Output 1. Dimensions shown in inches (mm). Tolerance 0.02 (0.5) max. Models Models 2. Mounting Holes A: 6-32 Mounting Screw, B: M3 x 0.5, Maximum mounting screw length from surface of chassis FAN is 0.14 inch (3.5 mm) A A 3. Input connector P1 is Dinkle P/N DT-35-B01W-03. 1.75 (44.45) Screws are M3 x 0.5 on 0.375 centres. 1.00 4. Connector P4 mates with Molex housing 50-37-5103 & pins (25.4) B B 5263. 5. Connectors P2. P3, P5 & P6: M3x0.5 screw connections. 0.63 (16.0) 6. Connector P7 mates with Molex housing 09-50-3041 & 2878 0.25 (6.35) 7.00 (177.8) series crimp terminals. 7.50 (190.5) 7. DC fan on P4 is rated at 12 V/0.1 A. 06-May-09