RDC4072D15 XP Power

DC-DC Power Supplies RDC40 Series 40 Watts 72 & 110 VDC Input for Railway Applications Single and Dual Outputs 1500 VAC Basic Isolation High Efficiency - Up to 90% Remote On/Off Complies with EN50155 EN50121-3-2 EMC for Railway Applications 3 Year Warranty Dimensions: The RDC40 series of 40W DC-DC converters are designed for railway applications and comply with RDC40: EN50121-3-2, the EMC standard for rolling stock apparatus. There are two input voltage ranges. 2.00 x 1.60 x 0.4 (50.8 x 40.6 x 10.16 mm) The 72 VDC nominal models accept an input from 36 to 140 VDC and the 110 V nominal versions have a 55 to 176 VDC input. A trim pin allows a +/-10% adjustment for single output models. Using convection cooling the converters have a wide operating temperature range of -40C to +85C and a maximum case temperature of 105C. Models & Ratings (1) Input Current Maximum (2) Input Voltage Output Voltage Output Current Efficiency Model Number Capacitive Load No Load Full Load 3.3 V 10.00 A 30 mA 526.82 mA 25000 F 87.0% RDC4072S3V3 5.0 V 8.00 A 30 mA 617.28 mA 2000 F 90.0% RDC4072S05 12.0 V 3.35 A 25 mA 641.76 mA 2500 F 87.0% RDC4072S12 36-140 VDC 15.0 V 2.65 A 25 mA 627.37 mA 2500 F 88.0% RDC4072S15 12.0 V 1.65 A 30 mA 632.18 mA 1600 F 87.0% RDC4072D12 15.0 V 1.35 A 30 mA 639.20 mA 1600 F 88.0% RDC4072D15 3.3 V 10.00 A 20 mA 344.83 mA 25000 F 87.0% RDC40110S3V3 5.0 V 8.00 A 25 mA 408.58 mA 2000 F 89.0% RDC40110S05 12.0 V 3.35 A 25 mA 420.06 mA 2500 F 87.0% RDC40110S12 55-176 VDC 15.0 V 2.65 A 25 mA 410.64 mA 2500 F 88.0% RDC40110S15 12.0 V 1.65 A 20 mA 413.79 mA 1600 F 87.0% RDC40110D12 15.0 V 1.35 A 20 mA 420.78 mA 1600 F 87.5% RDC40110D15 Notes 1. Input current specified at nominal 72 V or 110 V input. 2. Add suffix -HK for optional heatsink. Input Characteristic Minimum Typical Maximum Units Notes & Conditions 36 140 72 V nominal Input Voltage - Operating VDC 55 176 110 V nominal Input Current See models and ratings table Input Reflected Ripple 20 mA Through 12 H inductor and 33 F capacitor Input Filter Pi network OFF: 30.5 ON: 33.5 V 72 V models Undervoltage Lockout V OFF: 48.5 ON: 52.5 V 110 V models 150 72 V models (for 100 ms) Input Surge VDC 185 110 V models (for 100 ms) www.xppower.comDC-DC Power Supplies RDC40 Series Output Characteristic Min. Typ. Max. Units Notes & Conditions Output Voltage VDC See Models and Ratings table Output Voltage Trim 10 % On single outputs models only Minimum Load 0A Line Regulation 0.2 % 0.5 Single output models Load Regulation % 1.0 Dual output models (balanced outputs) Dual output models, when one load is varied between 25% and 100% and the other Cross Regulation 5 % is fixed at 100% Setpoint Accuracy 1 % Start Up Time 30 ms 100 mV pk-pk Single output models Dual output model 150 mV pk-pk Ripple and Noise Measured with 20 MHz bandwidth in parallel with 1 F ceramic capacitor across output rails Transient Response 4% Deviation, recovery to within 1% in <500 s for a 25% load change 3.9 3.3 V Models 6.2 5.0 V Models 15.0 12 V Models Overvoltage Protection V 18 15 V Models 15 12 V Models 18 15 V Models Overload Protection 130 % Of Full Load Short Circuit Protection Trip and restart (hiccup mode, auto recovery) Overtemperature Protection 115 C Case temperature On = Logic High (>3.0) or Open Remote On/Off Off = Logic Low (<1.2 V) or short pin 2 to 3 Maximum Capactitive Load See Models and Ratings table General Characteristic Minimum Typical Maximum Units Notes & Conditions Efficiency 88 % See Models and Ratings table Isolation: Input to Output 1500 VAC Input to Case 1600 VDC Output to Case 1600 VDC Switching Frequency 270 kHz 3 Power Density 31 W/in Mean Time Between Failure 320 kHrs MIL-HDBK-217F at 25 C GB Weight 0.105 (48) lb (g) Environmental Characteristic Minimum Typical Maximum Units Notes & Conditions Operating Temperature -40 +85 C See derating curve in Applications Note Case Temperature +105 C See derating curve in Applications Note Cooling Convection-cooled Operating Humidity 95 %RH Non-condensing Storage Temperature -55 +125 C www.xppower.com 2