600-800 Watts xppower.com SMR Series Up to 900 W Peak Output Power Single Outputs from 12 V to 48 V Compact Size Remote On/Off SEMI F47 Compliant Optional Current Share 3 Year Warranty Specification Input General Efficiency See model table Input Voltage 90-264 VAC (120-370 VDC) Isolation 3000 VAC Input to Output Input Frequency 47-63 Hz 1500 VAC Input to Ground Input Current SMR600: 9 A at 90 VAC, 3.5 A at 230 VAC 250 VDC Output to Ground SMR800: 11 A at 90 VAC, 5 A at 230 VAC Switching Frequency 60 kHz PFC, 25 kHz PWM typical Inrush Current 70 A at 230 VAC 3 3 Power Density SMR600: 6.16 W/In , SMR800: 8.2 W/In Power Factor >0.9 Signals Green LED for Power On, Power Good TTL Earth Leakage Current <2.4 mA max at 264 VAC HIGH within 100-500 ms and LOW Input Protection Fitted with a T12 A/250 V fuse 1 ms before loss of regulation Current Monitor 0.5 V to 3 V output denoting Output 0-100% output current MTBF 150 kHrs min to MIL-HDBK-217F Output Voltage See table at 25 C, GB Output Voltage Trim 5% Initial Set Accuracy 1% Environmental Minimum Load 1% (see note 9) Operating Temperature 0 C to +70 C, derates from 100% load at Start Up Delay 1.5 s at 230 VAC +50 C to 50% load at +70 C Start Up Rise Time 40 ms typical Cooling Integral fan Hold Up Time 16 ms min at 120 VAC Operating Humidity 5-90%, non-condensing Line Regulation 0.5%, low line to high line Storage Temperature -20 C to +85 C Load Regulation 1%, 1-100% load (see note 8) Operating Altitude 3000 m 2 Vibration 5-50 Hz, acceleration 7.35 ms on Over/Undershoot 5% max X, Y and Z axis Transient Response 5% max deviation, 500 s recovery to within 1% for a 50% load change EMC & Safety Ripple & Noise 1% of nominal output voltage (see note 2) Emissions EN55032, level B conducted and radiated Overvoltage Protection 110-130% recycle input to reset Harmonic Currents EN61000-3-2 class A Overtemperature Measured internally with auto recovery EN61000-3-2 class C for loads 20% Protection Voltage Flicker EN61000-3-3 Overload Protection 110-140% with auto recovery ESD Immunity EN61000-4-2, level 3 Perf Criteria A Short Circuit Protection Trip and restart (Hiccup mode) Radiated Immunity EN61000-4-3, 3 V/m Perf Criteria A Remote Sense Compensates for up to 0.5 V line drop EFT/Burst EN61000-4-4, level 2 Perf Criteria A (not available with current share) Surge EN61000-4-5, installation class 3 Remote On/Off On = TTL Logic HIGH, or open circuit Perf Criteria A Off = TTL Logic LOW or short circuit Conducted Immunity EN61000-4-6, 3V Perf Criteria A Current Share Optional single wire current share Dips & Interruptions EN61000-4-11, 30% 10 ms, 60% 100 ms, within 10% for up to 4 units 100% 5000 ms Perf Criteria A, B, B (add suffix -I to model number) Safety Approvals UL62368-1, CSA62368-1 via cUL, Note that this option includes output EN62368-1, blocking diodes. Remote sense is not SEMI F47 compliant (high line only) at available with current share. 100% rated power output AC-DCAC-DC L N SMR600-800 Models and Ratings Output Current Efficiency (7) (2) Output Power Output Voltage Ripple & Noise Model Number (1) Maximum Peak 115 VAC 230 VAC 600 W 12 V 50.00 A 75.00 A 120 mV 79% 83% SMR600PS12 600 W 24 V 25.00 A 37.50 A 240 mV 80% 85% SMR600PS24 600 W 48 V 12.50 A 18.75 A 480 mV 81% 86% SMR600PS48 750 W 12 V 62.50 A 75.00 A 120 mV 79% 83% SMR800PS12 800 W 24 V 33.33 A 37.50 A 240 mV 80% 85% SMR800PS24 800 W 48 V 16.67 A 18.75 A 480 mV 81% 86% SMR800PS48 Notes 1. Peak current can be taken for 500 s, average power should not exceed the 5. For U-channel versions replace SMR with SMS. maximum power. 6. For output currents >50 A please use remote sense to meet load 2. Ripple & Noise is measured using 0.1 F ceramic and 22 F electrolytic regulation ratings. capacitor, 20 MHz bandwidth. 7. Other output voltages available in OEM quantities, please contact sales. 3. Load regulation increases to 2% for 0-100% load change. 8. Minimum load required to meet ripple and noise specification. 4. For Top Fan versions replace SMR with SMT. Mechanical Details Covered Version A Mounting Hole 8 Places B Mounting Hole 8 Places 2.00 2.50 (50.8) (63.5) A B BA 0.22 (5.6) 0.22 (5.6) 0.25 (6.4) 0.25 (6.4) 2.09 1.59 5.00 (127.0) M4 (53.0) (40.4) CN3 UNC6-32 (Zn (yellow) -plated) (Zn-plated) Pin 7 1.59 6.00 (152.4) 2.50 (63.5) 2.50 (63.5) (40.3) Pin 1 A A B B 0.59 4.25 1.75 2.50 (15.0) (108.0) (44.45) (63.6) Voltage Trim B B 1.62 0.32 (8.25) (41.25) A A 1.25 (31.9) 0.88 (22.25) OPTION -D STANDARD Option -E Molex 9.17 (233.0) IEC320 or equivalent Terminal Block Part No. 09-91-2000 (20 pins) M3 Screw Terminal Blocks M3.5 Screw 8 Pins 9.5 mm center 3 Pins 8.25 mm center 2.50 A B B A (63.5) 2.00 (50.8) 9.17 (233.0) Options Option SMR SMT SMS CN3 (Signals) (1) Current Share + output blocking diodes -I -I -I Pin Function (1) Molex Output Connector -E -E -E 1 Current monitor (1) Molex Input Connector -F -F 2* Current share (1) -G -G Molex Input Molex Output 3 Return IEC320 Inlet -D 4 Power good (1) IEC Inlet Molex Outlet -F 5 Remote On/Off *If optional current share is (1) Available for OEM quantities, contact Sales. 6* -Remote sense fitted then remote sense function is For multiple option codes, place codes in alphabetical order, e.g 7* +Remote sense excluded. SMR800PS12-EI Notes 1. All dimensions are in inches (mm). 2. Weight: 3.30 lbs (1.5 kg) approx. 3. Tolerance: 0.012 (0.3) 4. Logic connector CN3 mates with: JST XHP-7 or equivalent & JST SXH-002T-P0.6 crimp terminals. 5. Maximum mounting screw penetration: 0.12 (3.0) on base & 0.25 (6.3) on each side. 6. Maximum screw terminal torque: Output: 15.7 lbs-in (1.8 Nm) Input: 7 lbs-in (0.8 Nm) VO+ VO- 0.07 (1.9) 0.02 (0.6) 0.07 (1.9) 0.02 (0.6)