TIME RELAY PCM-03 INSTRUCTION MANUAL Zakad Mechaniki i Elektroniki ZAMEL sp.j. J.W. Dzida, K. odziska ul. Zielona 27, 43-200 Pszczyna, Poland Tel. +48 (32) 210 46 65, Fax +48 (32) 210 80 04 www.zamelcet.com, e-mail: marketing zamel.pl DESCRIPTION TECHNICAL PARAMETERS The one mode time relay PCM-03 PCM-03 has a change over switch function in au- Input (supply) terminals: L, N tomation and control systems. The relay Input rated voltage: 230 V AC is released by power supply voltage. It Input voltage tolerance: -15 +10 % has a wide time adjustment range from 0,1s to 10 days. Additional ON/OFF func- Supply voltage control indicator: LED green tions enable constant switch on, switch Nominal frequency: 50 / 60 Hz off of the output (load). The system has Rated power consumption: 25 mA the indicators of power supply voltage, Operating mode number: 1 (flasher starting with off ) relay mode, and time measure with the Time adjustment range t: 0,1 s 10 dni help of red LED diode. Time measure accuracy: 0,2 % Time adjustment: 2x potentiometer (rotary + step) Power/relay supply indicator and time measure: LED red FEATURES Output relay parameters: 1NO/NC - 16 A / 250 V AC1 4000 VA Number of terminal clamps: 5 Operating mode: flasher starting from 2 Section of connecting cables: from 0,2 to 2,50 mm OFF (input voltage release), o Ambient temperature range: from -20 to +60 C supply voltage control indicator - LED Operating position: free green, Mounting: TH 35 rail (PN-EN 60715) power/relay supply indicator and time Protection degree: IP20 (PN-EN 60529) measure - LED red, Protection class: II time measure accuracy, Overvoltage category: II wide time adjustment range, Pollution degree: 2 constant switch on, switch off func- Rated impulse withstand voltage: 2 kV (PN-EN 61000-4-5) tion, Dimensions (height / width / depth): monomodular (17,5 mm) 90x17,5x66 mm relay output - 1 change-over contact Weight: 0,07 kg (NO/NC) contact max 16 A capacity, Reference standards: PN-EN 60730-1 TH 35 DIN rail installation. PN-EN 60730-2-7 PN-EN 61000-4-2,3,4,5,6,11 The device is designed for one-phase installation and APPEARANCE must be installed in accor- dance with standards valid Input supply terminal (A1) Input supply terminal (A2) in a particular country. The device should be connec- CAUTION ted according to the details included in this operating manual. Installa- tion, connection and control should be car- ried out by a qualified electrician staff, who act in accordance with the service manual and the device functions. Disassembling of Supply voltage control indicator Power/relay supply indicator the device is equal with a loss of guarantee and can cause electric shock. Before in- stallation make sure the connection cables are not under voltage. The cruciform head screwdriver 3,5 mm should be used to in- Smooth time adjustment stal the device. Improper transport, storage, and use of the device influence its wrong functioning. It is not advisable to instal the device in the following cases: if any device Time adjustment choice part is missing or the device is damaged or deformed. In case of improper functioning of the device contact the producer. The symbol stands for selective collection of electrical and electronic devices. Output (load) relay Placing used devices with other waste is not allowed terminals (11, 12, 14) VER. 001 14.09.2009MOUNTING FUNCTIONING 1. Disconnect the power supply from the ma- ins by the phase fuse, the circuit breaker or FLASHER STARTING WITH OFF - After the supply voltage U has been applied, the adjusted time t measurement starts. After the time t is over, the switch disconnector that are joined to the U the relay switches on (pos.11-14) and the adjusted time t is being measured proper circuit, once more. After the adjusted time t is over, the output relay R returns to the t t t t t t 2. Check if there is no voltage on connec- initial state,and the next operating cycle of the relay starts. The relay operates tion cables by means of a special measu- until the supply voltage is removed. re equipment, Diodes function 3. Install PCM-03 device in the switchboard on Time adjustment example t U description TH 35 DIN rail, 1h 10min 4. Connect the cables with the terminals accor- 5 6 10h relay switched off 1min 4 7 t = TIMExRANGE, 10s 1d 3 8 ding to installing diagram, (closed contacts 11-12), 1s ON 2 9 5. Switch on the power supply from the mains, time measure off t = 8 x 1 d = 8 d 1 10 0,1s OFF 6. Adjust the time using the TIME and RANGE relay switched on 1h knobs, where t=TIMExRANGE. 5 6 10min 10h 4 7 t = TIMExRANGE, 1min (closed contacts 11-14), 1d 10s 3 8 Switching on the power supply voltage cau- time measure on 2 9 1s ON t = 3 x 1 h = 3 h 1 10 ses the green LED luminosity. The cycle wil be 0,1s OFF (flashing diode) automatically initiated with the adjusted t time. CONNECTING EXAMPLE OF INSTALLATION PCM-03 time relay works as a supply impulse generator. It cooperates with PZM-10 flood relay contact switching on the alarm system cyclically in the moment of liquid detection at the sensor level. PRODUCT FAMILY PCM-03 time relay belongs to PCx time relay product family. DIMENSIONS INNER DIAGRAM Voltage type: 24V - 24 V AC/DC U - 12240 V AC/DC: available for PCM-01, PCM-02, PCM-03, PCM-06 U - 24250 V AC 30300 V DC: available for PCM-07 Device type: 01 - 1 operating mode switch on delay 02 - 1 operating mode switch off delay 03 - 1 operating mode cyclic change over 04 - 8 (PCP-04) or 10 (PCM-04) operating modes 06 - 2 operating modes - switch on/ switch off delay 07 - 25 operating modes, digital, two ranges of time operation 10 - 10 operating modes, two ranges of time RELAY CAPACITY operation Casing type: M - modular version (TH 35 DIN rail) P - flush junction box 60 version Device symbol GUARANTEE CARD There is 24 months guarantee on the product 1. ZMIE ZAMEL SP. J. assures 24 months guarantee for the product. 2. The manufacturers guarantee does not cover any of the following actions: a) mechanical damage during transport, loading / unloading or under other circumstances, b) damage caused by incorrect product mounting or misuse, c) damage caused by unauthorised modifications made by the PURCHASER or any third parties to the product or any other devices needed for the product functioning, d) damage caused by Act of God or any other incidents independent of the manufacturer. 3. The PURCHASER shall lay any claims in writing to the dealer or ZMIE ZAMEL SP. J. 4. ZMIE ZAMEL SP. J. is liable for processing any claim according to current Polish legislation. 5. ZMIE ZAMEL SP. J. shall process the claim at its own discretion: product repair, replacement or money return. 6. The manufacturers guarantee is valid in the Republic of Poland. 7. The PURCHASERs statutory rights in any applicable legislation whether against the retailer arising from the purchase contract or otherwise are not affected by this warranty. Salesman stamp and signature, date of sale VER. 001 14.09.2009 E E M M I I T T E E G G N N A A R R