n PCP - 04 TIME RELAY INSTRUCTION MANUAL Zakad Mechaniki i Elektroniki ZAMEL sp.j. J.W. Dzida, K. odziska ul. Zielona 27, 43-200 Pszczyna, Poland Tel. +48 (32) 210 46 65, Fax +48 (32) 210 80 04 www.zamelcet.com, e-mail: marketing zamel.pl DESCRIPTION TECHNICAL DATA The PCP-04 multifunction relay is de- PCP- 04 signed for timing function implementation Power terminals: L (black), N (blue) in automatics and control systems. Both Rated voltage: 230 V ~ power supply voltage and control input Rated voltage tolerance: -15 +10 % trigger the relay. The PCP-04 relay is Rated frequency: 50 / 60 Hz capable of operating in 8 independent op Rated current: 15,5 mA modes which may be triggered by means External trigger terminal: IN (triggered from L or N line) of either power supply voltage or external Trigger current: 510 A trigger impulse (from either L or N wires). Op modes quantity: 8 It is possible to adjust time within very wide range. The device is fitted with the t time adjustment range: 0,1 s 10 days (servo + continuous) relay state indicator the LED. It is pos- Time measure accuracy: 0,2 % sible to mount the device in the 60 mm Relay state and time measure indicator: red LED junction box. Relay contacts parameters: 1NO5 A / 250 V AC1 1250 VA (voltage contact) Connection terminals / leads quantity: 4 2 Connection wire section: 1 mm o Operating temperature: -20 +60 C FEATURES Operating position: optional 8 operating modes, Casing fastening: 60 mm junction box Relay state and time counting indica- Casing IP: IP20 (PN-EN 60529) tor LED, Protection class: II Triggered by means of power supply Overvoltage category: II voltage or control input in dependence Pollution level: 2 of set operating mode, Dimensions: 50 x 50 x 15 mm High accuracy of time measure, Weight: 30 g Relay output one changeover Standard conformity: PN-EN 60730-1 contact, 5 A maximum load, PN-EN 60730-2-7 Casing designed for mounting in PN-EN 61000-4-2,3,4,5,6,11 a junction box. The timer should be APPERANCE connected to a single- phase system accordin- gly to current standards. Time range selection The device connections CAUTION ON-time setting will be described in this Load / time measure indicator manual. Only qualified electricians are allowed to assembly, connect and ad- Trigger lead (IN) just the timer. It is necessary to read this Power lead (N) manual before the timer mounting. Do Load power supply lead (P) not disassembly the timer casing or you Power lead (L) will lose any warranty rights and expo- Operating mode selection se yourself to the electric shock hazard. Before mounting operation make sure of disconnecting the connection wires from the electric network. The timer should be carried, stored and used in an appropriate way. Do not mount the timer in case of any device parts lack, damage or deformation. In case of mal- function please notify the manufacturer. k w e c d o u a l r l e b b b rASSEMBLY OPERATION 1. Disconnect the electric network by Power supply voltage trigger: means of an appropriate cut-off, DELAYED SWITCH-ON t time will be measured after power supply current-limiting circuit-breaker or U voltage has been switched ON. When the t time is over, the relay will A be ON. The op mode will be triggered again after power supply voltage t t separator. MODE switching OFF and ON again. 2. Check if there is no any voltage DELAYED SWITCH-OFF the relay will be ON just after power supply between power leads by means of U voltage switching ON and the t time will be measured. When the t time B an appropriate gauge. is over the relay will be OFF. The operating mode will be triggered again t t after power supply voltage switching OFF and ON again. MODE 3. Mount the PCP-04 device in the 60 CYCLIC SWITCHING (starts from the OFF state) t time will be measured mm junction box. U after power supply voltage has been switched ON. When the t time is over, the 4. Connect wires according the electri- C relay is ON. Then the relay will be switched alternatively in t time cycles. The t t t t t t cal diagram. operating mode will be OFF when power supply is OFF. MODE 5. Connect power supply circuit. External impulse trigger: 6. Select the op mode by means of the TIME IMPULSE TRIGGERED WITH RISING EDGE when supplied, the MODE switch. S module will switch ON the relay when trigger impulse rising edge comes. D Then the preset time will be measured. When t time is over, the relay will t t 7. Select time by means of the TIME be OFF. Trigger impulse duration is irrelevant. handwheel and the RANGE switch, TIME IMPULSE TRIGGERED WITH TRAILING EDGE when supplied, MODE where t = TIME x RANGE. the module will switch ON the relay when trigger impulse trailing edge S E comes. Then the preset time will be measured. When t time is over, the t t relay will be OFF. Successive trigger impulse decays during t time dura- tion will not cause time counting reset (non-retriggerable circuit). DELAYED SWITCHING ON / OFF when supplied, the module will not LOAD MODE switch ON the relay and will start t time measure when trigger impulse S rising edge comes. When t time is over, the relay will be ON t time will be F t t t t t counted once again when trigger impulse trailing edge comes. When t 375 W 180 W time is over, the relay will be OFF. If the impulse duration is shorter than t time, the relay will be ON for t time only. 90 W 150 W BISTABLE RELAY WITH TIME LIMIT when supplied, the module will switch ON the relay and start t time measure when trigger impulse rising S G MODE edge comes. The relay will be switched OFF when the next trigger impul- t t t se rising edge comes or after t time has been over if the trigger impulse do not come. The impulse duration is irrelevant for the circuit operation. CASING DIMENSIONS TIME IMPULSE TRIGGERED WITH RISING EDGE WITH DELAYED SWITCH OFF (retrigerrable) when supplied, the module will switch ON S the relay when trigger impulse rising edge comes. When trigger impulse H t t t t trailing edge comes, t time will be measured and when the time is over, the t relay will be OFF. Successive trigger impulse trailing edge will cause t time MODE counting reset and measure from the beginning (retrigerrable). Multiplier: 0,1 s 1 s 10 s 1min. MODE 10 min. 1 hour 10 hours 1day PRODUCT FAMILY The PCP-04 time relay is a member of the PCX product family. RANGE RANGE RANGE RANGE RANGE RANGE RANGE RANGE 24 VAC/DC power supply Device version: 01 - mode: delayed ON CONNECTIONS 02 - mode: delayed OFF 03 - mode: cyclic changeover 04 - few op modes 10 - 10 modes,two periods L/N adjustment Casing type: M - single-module (double-module for 10 ver.) P - for junction box Device type WARRANTY The product warranty is for a period of 24 months 1. ZMIE ZAMEL SP. J. assures 24 months guarantee for the product. 2. The manufacturers guarantee does not cover any of the following actions: a) mechanical damage during transport, loading / unloading or under other circumstances, b) damage caused by incorrect product mounting or misuse, c) damage caused by unauthorised modifications made by the PURCHASER or any third parties to the product or any other devices needed for the product functioning, d) damage caused by Act of God or any other incidents independent of the manufacturer. 3. The PURCHASER shall lay any claims in writing to the dealer or ZMIE ZAMEL SP. J. 4. ZMIE ZAMEL SP. J. is liable for processing any claim according to current Polish legislation. 5. ZMIE ZAMEL SP. J. shall process the claim at its own discretion: product repair, replacement or money return. 6. The manufacturers guarantee is valid in the Republic of Poland. 7. The PURCHASERs statutory rights in any applicable legislation whether against the retailer arising from the purchase contract or otherwise are not affected by this warranty. Dealer signature & stamp, purchase date n k e c w d u a o e l l r b b r b