RZB-03 WIRELESS CONTROL SET CoNNECtioN SRP-02 MouNtiNG ROLLER BLINDS CONTROL MANUAL INSTRUCTION 1. Disconnect power supply by the phase fuse, the circuit-breaker or the switch-disconnector LOCAL LOCAL combined to the proper circuit. 2. Check if there is no voltage on connec- tion cables by means of a special measure equipment. ZAMEL Sp. z o.o. 3. Connect the cables with the terminals in ac- cordance with the installing diagram. 4. Install SRP-02 device in installation cable box. ul. Zielona 27, 43-200 Pszczyna, Poland 5. Switch on the power supply from the mains. tel. +48 (32) 210 46 65, fax +48 (32) 210 80 04 www.zamelcet.com, e-mail: marketing zamel.pl RNK-02 FuNCtioNiNG, MouNtiNG DESCRiPtioN tECHNiCAL DA t A By pressing the button, the transmitter sends a RNK-02 SRP-02 SRP-02 controller is used to control signal with 868,32 MHz frequency which controls roller blind drives with 230V AC motor with Input (supply) terminals: - L, N EXTA FREE receivers. Device programming a limit switch. The device realises roller CAutioN: Input rated voltage: 3 V DC (CR2032 battery) 230 V AC procedure (adding a transmitter to a receiv- blinds local and central control functions Local switches connection (LoCAL) is optional. ers memory) is described in particular EXt A Battery life: 3 5 years - and it has the possibility of comfort mode FREE manual instructions. The device range Input voltage tolerance: - +10 -15 % adjustment. Comfort modes are used to (up to 250 m depending on a receiver) can be in- Nominal frequency: - 50 / 60 Hz adjust roller blinds position (height level) APPLiCAtioN creased by means of a retransmitter or few RTN- and to memorise the height level. Central Nominal power consumption: - 0,4 W (stand-by mode) / 0,7 W (roller blind movement) 01 retransmitters. The device can be mounted in mode is used in case of a totally closed Transmission: radio 868,32 MHz any place by means of double-sided adhesive or opened roller blind or a group of roller Coding way: unidirectional tape or two wall plugs (5x(3x30) mm. blinds with different position level. Coding: addressing transmission Maximum number of remote controls: - 32 Mounting by means of wall plugs: 1. Remove the button - to do it press the button Range: up to 250 m in the open area on one side, and on the other side put a screw- Maximum movement time of roller blind: - 120 sec driver into a slot and lift up the button. Maximum time of roller blind movement: - 1 120 sec (every 0,1 sec) 2. Find a place on the wall to mount the transmit- Optic signalling of transmitters operation: LED red diode ter, make two holes corresponding mounting FEAtuRES Local control terminals: - LOCAL (up), (down) holes from the transmitters base. Motor power supply terminals: - (up), (down) 3. Set wall plugs in the holes. Complete set of wireless control Relay contact parameters: - 2NO 5A/250V AC AC3 1250 VA 4. Fix the base by means of screwing screws into (2channel button radio transmitter RNK-02 and radio roller blinds controller Number of terminal clamps: - 6 wall plugs. 2 SRP-02), 5. Place the button again. Section of connecting cables: - up to 2,5 mm used in wired and wireless control of o Ambient temperature range: -10 +55 C roller blind, sunblind and gate drives, BAttERY CHANGE Operating position: free (electric motors of 230V AC), Battery discharge status is signalled by sev- Casing mounting: wall plugs, double-sided adhesive tape installation cable box 60 mm wired local control inputs, eral LED red diode flashes during transmis- Casing protection degree: IP20 (EN 60529) easily installed in 60 mm junction box, sion time. energy-saving device, possibility of con- Protection level: III II 1. Remove the button (mounting - point 1). stant work, Overvoltage category: - II 2. By means of a screwdriver lever up the printed- two comfort modes - upper and bottom Pollution degree: 2 circuit board releasing the bottom latch and re- (memory of roller blind height level), move it from the base. Surge voltage: - 1 kV (EN 61000-4-5) possibility of cooperation with any roler 3. Remove the battery from the latch. Dimensions: 90 x 80 x 11,5 mm 47,5 x 47,5 x 20 mm blind switch (which is not equipped in 4. Mount a new battery. Watch battery polari- Weight: 0,038 kg 0,039 kg backlight elements) sation marked on the latch. Wrong battery Reference standard: ETSI EN 300 220-1 EN 60669, EN 60950, mounting may cause device damage. ETSI EN 300 220-2 EN 61000 5. Put the removed printed-circuit board back in Radio flush dimmer RNK-02 operating roller The device is designed for the base. blind controller SRP-02 (roller blind opening / single-phase installation and 6. Put back the button. APPEARANCE closing). The above mentioned transmitter can must be installed in accord- ance with standards valid in be added to any number of receivers. Local wired control terminals CAutioN: a particular country. The de- (upward movement , downward movement ) While changing the battery, it is suggested to vice should be connected ac- CAutioN cording to the details included Roller blind motor terminals press any of the buttons for about 5 seconds The ZAMEL company in this operating manual. Installation, connection (upward movement , downward movement ) before putting it into a latch. Next press trans- devices which are and control should be carried out by a qualified mission button several times to check its op- Input (supply) terminals (L, N) characterised with this sign electrician staff, who act in accordance with the can cooperate eration. if the transmitter does not work prop- service manual and the device functions. with each other. erly repeat the battery change procedure. In case of casing dismantling an electric shock may occur, and the guarantee is lost then. Before Optic signalling of receivers operation installation make sure the connection cables are Programming push-button WARRANtY CARD not under voltage. The cruciform head screwdriv- er 3,5 mm should be used to instal the device. Im- Optic signalling proper transport, storage, and use of the device There is 24 months guarantee on the product of transmitters operation influence its wrong functioning. It is not advisable 1. ZAMEL provides a two-year warranty for its products. to instal the device in the following cases: if any 2. The ZAMEL warranty does not cover: a) mechanical defects resulting from transport, loading / unloading or other circumstances Push-button device part is missing or the device is damaged b) defects resulting from incorrect installation or operation of ZAMEL products c) defects resulting from any changes made by CUS- TOMERS or third parties, to products sold or equipment necessary for the correct operation of products sold d) defects resulting or deformed. In case of improper functioning of from force majeure or other aleatory events for which ZAMEL is not liable e) power supply (batteries) to be equipped with a device the device contact the producer. in the moment of sale (if they appear) 3. All complaints in relation to the warranty must be provided by the CUSTOMER in writing to the retailer after discovering a defect. 4. ZAMEL will review complaints in accordance with existing regulations. The symbol means selective 5. The way a complaint is settled, e.g. replacement of the product, repair or refund, is left to the discretion of ZAMEL. collecting of electrical and electronic 6. Guarantee does not exclude, does not limit, nor does it suspend the rights of the PURCHASER resulting from the discrepancy equipment. between the goods and the contract. It is forbidden to put the used equipment together with other waste Salesman stamp and signature, date of sale VER. 003 20.05.2011SRP-02 oPERAtioN RADio tRANSMittERS DELEtioN Pressing shortly the programmed push-button in local mode (<2 sec.) or roller blind switch (optional) causes the roller blind moves. Another short pressing of the same push-button or the switch causes the roller blind stops at a required level. Pressing the push-button or the switch longer (>2 sec.) causes comfort mode activates (the roller blind moves in required direction and stops according to the adjusted time). Pressing shortly transmitters push-button (programmed in central mode) causes complete opening or closing the roller blind. Press PROG push-button of SRP-02 After 5 seconds LED red diode switches on Release the push-button in SRP-02 - RADio tRANSMittERS PRoGRAMMiNG device for a longer time. (signal pulsates) and then it switches off. MEMORY IS DELETED. LoCAL mode: CooPERA tioN AND oPERA tiNG RANGE Symbol RoP-01 RoP-02 RoB-01 SRP-02 SRP-03 RWG-01 RWL-01 RoM-01 RoM-10 RDP-01 RtN-01 RNK-02 180 m 200 m 200 m 200 m 200 m 250 m 180 m 250 m 250 m 180 m 250 m RNK-04 180 m 200 m 200 m 200 m 200 m 250 m 180 m 250 m 250 m 180 m 250 m Press PROG push-button of SRP-02 device Press and release transmitters first Press and release the second P-256/8 230 m 250 m 250 m 250 m 250 m 300 m 200 m 300 m 300 m 230 m 300 m for a longer time until LED red diode switches on push-button (movement ). LED red transmitters push-button (constant signal). Next release PROG push-button. diode switches on (first signal pulsates, (movement ). LED red diode switches on P-257/4 (2) 180 m 200 m 200 m 200 m 200 m 250 m 180 m 250 m 250 m 180 m 250 m next the signal is constant). (signal pulsates) and then switches off - RNM-10 230 m 250 m 250 m 250 m 250 m 300 m 200 m 300 m 300 m 230 m 300 m THE TRANSMITTER IS ADDED. RNP-01 160 m 180 m 180 m 180 m 180 m 200 m 160 m 200 m 200 m 160 m 200 m CENtRAL mode: RNP-02 160 m 180 m 180 m 180 m 180 m 200 m 160 m 200 m 200 m 160 m 200 m RNL-01 160 m 180 m 180 m lack* lack* 200 m 160 m 200 m 200 m 160 m 200 m RtN-01 200 m 200 m 200 m 200 m 200 m 250 m 200 m 250 m 250 m 200 m 250 m RCR-01 160 m 180 m 180 m lack* lack* 200 m 160 m 200 m 200 m 160 m 200 m Rti-01 160 m 180 m 180 m 180 m 180 m 200 m 160 m 200 m 200 m 160 m 200 m RXM-01 230 m 250 m 250 m 250 m 250 m 300 m 200 m 300 m 300 m 230 m 300 m Press PROG push-button of SRP-02 device Press and release transmitters first Press and release the second for a longer time until LED red diode switches on push-button (movement ...). LED red transmitters push-button (movement ...). (constant signal). Next release PROG push-button. diode switches on (first signal pulsates, LED red diode switches on (the signal * -1-channel transmitters do not cooperate with roller blind controllers. Wait (for about 5 seconds) till LED red diode switches next the signal is constant). pulsates) and next it switches off - on (first signal pulsates, next the signal is constant). THE TRANSMITTER IS ADDED. CAUTION: The given range concerns open area - an ideal condition without any natural or artificial obstacles. If there are some obstacles between a transmitter and a receiver, it is advisable to decrease the range according to: wood and plaster: from 5 to 20 %, bricks: from 10 to 40 %, reinforced concrete: from 40 to 80 %, metal: from 90 to 100%, glass: from 10 to 20 %, over- and underground medium and high electrical power lines, radio and television transmitters, GSM transmitters set close to a device system have also a negative influence on the range. An exemplary programming procedure with P-257/4 remote control. The procedure for the rest of radio EXTA FREE transmitters is analogous with reservation that 2-channel transmitters can be programmed only in one mode - local or central. RANGE LoSS CoNCERNiNG RADio SiGNALS GoiNG tHRouGH oBSt ACLES CAutioN: if push-button changes are required for local and central control (in 4-channel transmitter) the programming procedure should be for two modes separately (first local control push-buttons, then central control push-buttons). In case of 2- channel transmitter the change from local control to central control should start with controllers memory deletion and only then transmitte- rs programming procedure for central mode can start. one transmitter can be added during one programming cycle. Full memory is signalled with pulsating LED red diode. CoMFoRt MoDE tiME PRoGRAMMiNG bricks: from 10 to 40 %, wood and plaster: from 5 to 20 %, reinforced concrete: from 40 to 80 %, metal: from 90 to 100%, glass: from 10 to 20 % tRANSMittERS RECEiVERS RNK-02 RNL-01 RoP-01 RWL-01 2channel button Radio 1-channel Radio lighting radio transmitter foot transmitter radio receiver switch RNK-04 Rti-01 RoP-02 RWG-01 Open the roller Press PROG push-button of SRP-02 device for a longer time until Wait again (for about 5 seconds) till 4-channel button IR/EXTA FREE 2-channel Remote control blind completely. LED red diode switches on (constant signal). Next release PROG LED red diode switches on (first signal radio transmitter transceiver radio receiver socket push-button. Wait (for about 5 seconds) till LED red diode switches pulsates, next the signal is constant). on (first signal pulsates, next the signal is constant). P-256/8 RNM-10 RDP-01 SRP-02 8-channel 4-channel radio 1-channel Radio roller blinds remote controller modular transmitter radio dimmer controller P-257/4 RNP-01 RoB-01/12-24V SRP-03 4-channel 4-channel Radio Central radio roller remote controller radio transmitter gate controller blinds controller P-257/2 RNP-02 RoM-01 RoM-10 2-channel 4-channel 1-channel radio 2-channel remote controller radio transmitter modular receiver radio modular receiver RCR-01 RXM-01 If the roller blind is in a required Press PROG push-button of SRP-02 device, Radio Translator comfort position - press PROG push- next release PROG push-button - the roller motion sensor RS-485/EXTA FREE button and release it - the roller blind blind moves automatically. stops - ROLLER BLIND MOVEMENT ACCESSoRiES TIME IS ADDED. ANt -01 RtN-01 Time programming example for upper comfort mode. In order to programme time for bottom comfort mode, it is necessary to close the roller blind completely External antenna Retransmitter before programming procedure starts. Maximum time is 120 seconds. VER. 003 20.05.2011