ARTESYN DS1200 1200 Watts Distributed Power System Advanced Energy s Artesyn DS1200 series is Artesyn DATA SHEET Embedded Power highest power, highest density bulk front end AC-DC power supply in the industry standard 1U x 2U Distributed Power Bulk form factor. It accepts a wide range 90264 Vac input and Front-End provides a main 12 V output plus a 3.3 V or optional 5.5 V Total Output Power: standby output. Rated at 1,100 watts, it has a high half-load 1200 Watts efficiency of 91%. Housed in an industry standard 1U x 2U +3.3 Vdc Stand-by Output rack-mounting package, the power supply is designed for Wide Range Input Voltage: servers and similar space-constrained applications. This 90 - 264 Vac series comes in two airflow versions dc-connector to ac-connector and vice versa. EEPROM for FRU data SPECIAL FEATURES Red/green bi-color LED status Active power factor correction Internal fan speed control EN61000-3-2 harmonic compliance Fan Fail Tach Output Signal Active AC inrush control Full digital control 1U X 2U form factor Two year warranty 3 21.71 W/in +12 Vdc Output SAFETY +3.3 Vdc or +5.0 Vdc stand-by No minimum load required UL/cUL 60950 (UL Recognized) Hot plug operation NEMKO+ CB Report EN60950 N + 1 redundant EN60950 Internal ORing fets CE Mark Active current sharing (10 - 100% China CCC load) Built-in cooling fan (40 mm x 28 mm) 2 I C communication interface bus PMBus compliant 2020 Advanced Energy Industries, Inc.DS1200 ELECTRICAL SPECIFICATIONS Input Input range: 180 - 264 (1200 W) 90 - 264 (1000 W) Frequency: 47-63 Hz, single phase AC Inrush current: 40 Apk maximum inrush current Efficiency: > 91% typical at high line 50% load Conducted EMI: FCC Subpart J EN55022 Class B Radiated EMI: FCC Subpart J EN55022 Class B Power factor: 0.99 typical Leakage current: 1.40 mA 240 VAC Hold up time: 12 ms minimum Output Main DC voltage: +12 V 100 A (high line) +12 V 81.6 A (low line) Stand-By: +3.3 Vsb 6 A (5 V 4 A available) Adjustment range: 5% on +12V only using I2C Regulation: +12 Vdc +5%/-5% +3.3 Vsb +5%/-5% Over current: +12 Vdc latches off if overcurrent lasts over 1 second, otherwise it is auto recovery (See Table 1 next page) +3.3 Vsb, 9 A max (hiccup mode) Over voltage: +12 Vdc 13.2 - 14.4 Vdc +3.3 Vsb 3.76 - 4.30 Vdc Under voltage: +12 Vdc 9 - 10.8 V (latch off) Turn-on delay: 2 second max, 5 - 50 mS, monotonic rise Main output rise time: 5 - 50 mS, monotonic rise LOGIC CONTROL PS SEATED (A4): TTL logic LOW if power supply is seated into system connector. This is a short pin. A logic HIGH if the PSU is removed PWR GOOD (C3): Active TTL high when output is within regulation limits. AC OK (B1): A low logic level if the input voltage is within allowable limits. A TTL logic HIGH level, and a 5mS early warning signal before 12.0 V DC output loss of regulation. PS INHIBIT/PS KILL (B4): When left open power supply operation will be inhibited. When the power supply is inserted into the system, this pin will be pull low by the system and turn the power supply on only after all other power supply pins have seated. PS ON (A1): The output will be enabled when this signal is pulled low, below 0.8 V outputs disabled when pin is driven high or left open. 2 advancedenergy.com