POWER Data Sheet DS460S 460 Watts Total Output Power: 460 Watts +12 Vdc Stand-by Output Wide Range Input Voltage: 90 - 264 Vac Special FeatureS Active power factor correction EN61000-3-2 harmonic compliance Active AC inrush control 1U X 2U form factor +12 Vdc output +12 Vdc stand-by Hot plug operation Electrical Specifications N + 1 redundant Input Active current sharing Built-in cooling fan Input ra nge: 90 - 264 Vac 2 I C communication interface bus Frequency: 47 - 63 Hz, single phase AC PMBus compliant Inrush current: 30 Apk maximum inrush current EEPROM for FRU data Efficiency: 92% typical at high line 50% load Two years warranty Conducted EMI: FCC Subpart J EN55022 Class A Radiated EMI: FCC Subpart J EN55022 Class A SaFety Power factor: 0.99 typical UL/cUL 60950 (UL Recognized) Leakage current: 1.0 mA 240 Vac NEMKO 60950 Hold up time: 10 ms minimum Cb Certificate and report Output CE Mark (LVD) Main DC voltage: +12.3 V 36.0 A Stand-By: +12 V 2.3 A Adjustment range: Factory Set Regulation: 11.85 - 12.45 Vdc 11.40 - 12.6 Vdc Overcurrent: +12 Vdc latches off if overcurrent lasts over 1 second, Trip point 120% - 150% of rated current. Overvoltage: +12 Vdc 13.6 - 15.0 Vdc +12 Vsb 13.6 - 15.0 Vdc Turn-on delay: 1 - 1.5 seconds Main output rise time: 10 - 30 mS, monotonic riseDS460S Data Sheet Logic Control PS PRESENT (S4): Used to sense the number of power supplies in the system (operational or not) and provide hot plug insertion and removal functionality by controlling main outputs during hot plug insertion and removal by employing following circuitry. When the unit is removed from the system the fast shut down signal quickly turns OFF main outputs and discharges output capacitors. This signal is the shortest gold finger pin on the signal connector to allow for last make, first break configuration. PSOK (S6): Combined indicator of AC input and main 12 V DC output. This is a three level signal to indicate different stages as follows. AC not OK and DC not OK Signal status shall be LOW (< 0.6 V) AC OK and DC not OK Signal status shall be LOW (< 0.6 V) AC OK and DC OK Signal status shall be HIGH (> 3.0 V) AC not OK and DC OK Signal status shall be Middle Level (Between 2 V and 2.5 V) DC OK threshold is defined as when the 12 V output is greater than 11.5 V. DC not OK threshold is defined as when the 12 V output is less than 11.4 V & greater than 11.3 V. I-Mon (S7): Provides both the load sharing function (as a feedback for output regulation droop function) and 12 V output current information. PS INTERRUPT (S4): The signal behavior in response to certain operating condition changes in the power supply as defined in the Firmware Specification section. This signal shall be pulled up to maximum 5 V logic level external to the PS. PS ON (S8): Required to remotely turn on/off the power supply. PSON is an active low signal that turns on the main 12 V DC output. When this signal is not pulled low by the system, or left open, the 12 V output is turned off. This signal is pulled to a standby voltage by a pull-up resistor internal to the power supply. Refer to On/Off Timing for timing dia- gram in TRN. When in off or standby condition, the main 12 V DC output will be less than 50 mV with respect to output return. Environmental Specifications Operating temperature: -10 C to 50 C Storage temperature: -40 C to +85 C Altitude, operating: 10,000 ft. Electromagnetic susceptibility/Input transients: -EN61000-3-2 -EN61000-4-2, 4.3, 4-4, -4-5, 4-6, 4-11 RoHS & lead-free compliant No tantalum caps. Humidity: 5 to 90% RH, non-condensing Shock and vibration specificatons: Complies with Astec Std. Specifications MTBF (Demonstrated): 500K Hrs at full load, 50 C Ordering Information Nominal Output Set Point Total Minimum Maximum Output Ripple Model Number Over Current Stand-by Air Flow Voltage Set Point Tolerance Regulation Current Current P/P DS460S-3-002 12.3 Vdc 0.2% +5% 1 A 36.0 A 120 mV 45.9 A - 57.5 A* 12.0 V 2.3 A STD DS460S-3-003 12.3 Vdc 0.2% +5% 1 A 36.0 A 120 mV 45.9 A - 57.5 A* 12.0 V 2.3 A REV DS460S-3-004 12.3 Vdc 0.2% 5.0% 1.0 A 36.0 A 120 mV 45.9 A - 57.5 A* 12.0 V 2.3 A STD (5,000 m) DS460S-3-005 12.3 Vdc 0.2% 5.0% 1.0 A 36.0 A 120 mV 45.9 A - 57.5 A* 12.0 V 2.3 A REV (5,000 m) *Overcurrent latches off if overcurrent lasts over 1 second, otherwise it is auto recovery.