DS760SL-3-001 Artesyn Embedded Technologies

POWER DS760SL Series Data Sheet 760 Watts Bulk Front End Total Output Power: 760 Watts +5.0 Vdc Standby Special feaS 760 W output power 18.1 W/cu-in 1U X 54.5 mm form factor (slimline) N + 1 redundant Hot-swap Internal ORing 5.0 V housekeeping High efficiency 91% 230 Vac, Electrical Specifications 50% load Input Variable speed smart fans Input ra nge (operating) 90 - 264 Vac EMI Class A Input range (nominal) 115 / 230 Vac Input through IEC connector EN61000 Immunity Frequency 47 - 63 Hz Two year warranty Input fusing Internal 10 A fuses Both lines fused Inrush current < = 25 A peak Either hot or cold start SY Power factor 0.99 typical Meets EN61000-3-2 UL/cUL 60950-1 Harmonics Meets IEC 1000-3-2 requirements CSA 60950-1 Input current 8.8 A RMS max input current At 100 Vac VDE 60950-1 Holdup time 12 ms minimum for main O/P At full rated load China CCC 20 ms minimum for standby CB Scheme Report/Cert Undervoltage lockout 85 2.5 Vac Turn-on voltage 80 2.5 Vac Turn-off voltage Overvoltage lockout N/A Leakage current < 0.8 mA At 264 Vac On/Off power switch N/A Power line transient MOV directly after the fuse Environmental Specifications Operating temperature -10 to 50 C Storage temperature -40 to 85 C Cooling Internal fan (fan speed control) Operating relative humidity 5% to 95% non-condensing Altitude 10,000 feet RoHS compliant Yes afet tureDS760SL Series Data Sheet Ef ciency Curve 760 W DS Slim (STD Air) 92.0% 90.0% 88.0% 230 Vac, 50Hz 86.0% 115 Vac, 60Hz 84.0% 82.0% 80.0% 0.0 100.0 200.0 300.0 400.0 500.0 600.0 700.0 800.0 900.0 Output Power W Output Output rating 12 V 62.3 A 748 W 90 - 264 Vac 5.0 Vsb 2.4 A 12 W Setpoint 12.0 V Total regulation range 12 V 1% Line/load/transient when measured at output 5.0 Vsb 3% connector Rated load 760 W maximum No derating over operating temp range Minimum load 12 V 0.0 A No loss of regulation 5.0 Vsb 0.0 A Output noise (PARD) 100 mV Max P-P 12.0 V output 100 mV Max P-P 5.0 Vsb output Measured with a 0.1 uF ceramic and 10 uF tantalum capacitor on any output 20 Mhz Output voltage overshoot 300 mV 12 V main 1 A/uSec slew rate 200 mV 5.0 standby Transient response < 250 uSec 50% load step 1 A/us Step load valid between 10% to 100% of output rating Recovery time to within 1% of set point at onset of transient Max units in parallel Up to 4 Short circuit protection To 120% of rated output Output to return Remote sense Compensation up to 100 MV Output isolation Standard per Safety Requirements Forced load sharing To within 10% of all shared outputs Digital sharing control Overload protection (OCP) 120% to 130% 12 V output 120% to 170% 5.0 Vsb output Overvoltage protection (OVP) 110% to 120% 12 V outpu 110% to 125% 5.0 Vsb output Overtemperature protection 10 - 15 C above safe operating area Both PFC and output converter monitored Ordering Information O/P Voltage Set Point Total Minimum Maximum Output Stand-by Model Number Air Flow Set Point Tolerance Regulation Current Current Ripple P/P Voltage DS760SL-3 12.0 Vdc 0.2% 1% 0 A 62.3 A 120 mV 5.0 V 2.4 A Standard DS760SL-3-001 12.0 Vdc 0.2% 1% 0 A 50.0 A 120 mV 5.0 V 2.4 A Reverse DS760SL-3-002 12.0 Vdc 0.2% 1% 0 A 62.3 A 120 mV 3.3 V 2.4 A Standard DS760SL-3-003 12.0 Vdc 0.2% 1% 0 A 50.0 A 120 mV 3.3 V 2.4 A Reverse Ef ciency